Calculation of Cylinder-Flat Gauge under 0.56 mm Heel-Toe Difference Flat with 3 mm-Long Plane Ground on Setover

Yan Hong Li; Ji Peng Cao; Peng Zi Sun

doi:10.4028/www.scientific.net/AMM.197.154

Paper Titles

Study on Performance of Automobiles Muffler Based on Sound Transfer Matrix Theory
p.134

Research on Thermally Induced Deformation of Reinforcing Plate Based on Finite Element Simulation
p.139

Investigation on the Prestage of a Water Hydraulic Jet Pipe Servo Valve Based on CFD
p.144

The Comparison and Selection of the Solutions for Liuyang River Tunnel’s Inclined Shaft Entering to the Main Hole and the Key Points of Construction
p.149

Calculation of Cylinder-Flat Gauge under 0.56 mm Heel-Toe Difference Flat with 3 mm-Long Plane Ground on Setover
p.154

Pitching Dynamic Response of Variable Sweep Wing Aircraft
p.159

High Precision Modeling and Identification of the Near Transition Sliding Friction in a Mechanical Stage
p.164

Design of Servo Peristalsis Dispenser Based on Motion Controller and Touch Screen
p.169

Three Dimensional Finite Element Interference Contact Analysis about Cone Screw and Bush of Opposed Biconinal Cone Screw High-Pressure Seawater Hydraulic Pump
p.174

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 197Calculation of Cylinder-Flat Gauge under 0.56 mm...

Calculation of Cylinder-Flat Gauge under 0.56 mm Heel-Toe Difference Flat with 3 mm-Long Plane Ground on Setover

Abstract:

The cylinder-flat gauge of 0.56 mm heel-toe difference (HTD) flat with 3 mm-long plane ground on setover was calculated by the method of geometry. The change curves of cylinder-flat gauge were given by using MATLAB software under three conditions of 0.56 mm HTD flat, 0.56 mm HTD flat with 3 mm-long plane ground on setover, and 0.49 mm HTD flat. It conclude that the average gauge under 0.49 mm HTD adopted is smaller than that under 0.56 mm HTD flat with 3 mm-long plane ground on setover, and 0.49 mm HTD is realized easily in processing.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 197)

Pages:

154-158

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.197.154

Citation:

Cite this paper

Online since:

September 2012

Authors:

Yan Hong Li, Ji Peng Cao, Peng Zi Sun

Keywords:

0.56 mm Heel-Toe Difference Flat with 3 mm-Long Plane Ground on Setover, Carding Machine, Cylinder-Flat Gauge, Flat Heel-Toe Difference

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] K. Hiroshi, H. Susumu. Journal of the Textile Machinery Society of Japan Vol. 29(1976), p.41.

Google Scholar

[2] Jia-cai Chen, Zhi-yong Mao. Cotton Textile Technology Vol. 11(1983), p.7.

Google Scholar

[3] Zong-sheng WEI. Journal of Textile Research Vol. 9(1987), p.36.

Google Scholar

[4] Research Center of China Textile Industry. Practice technology of carding machine (Research Center of China Textile Industry Publications, Taibei 1991).

Google Scholar

[5] Da-nian Qiu. Shandong Textile Technology Vol. 2(1994), p.48.

Google Scholar

[6] Da-nian Qiu. CN Patent No. 2190658. (1995).

Google Scholar

[7] Qing Fei. Beijing Textile Journal Vol. 19(1998), p.22.

Google Scholar

[8] Long-kui Ran, Li-dan Xi. Cotton Textile Technology Vol. 29(2001), p.15.

Google Scholar

[9] Peng-zi Sun, Yan-qing Ju, Ming-guang Zhang. Journal of Donghua University (Eng. Ed. ), Vol. 24(2007), p.657.

Google Scholar

[10] P.Z. Sun, Y.Q. Ju, Y.H. Li, J.P. Cao. Journal of The Textile Institute (2013), in press.

Google Scholar

[11] Duane Hanselman, Bruce Littlefield, translated by Ren-feng Zhu. Mastering MATLAB 7 (Tsinghua University Press, Beijing, China 2006).

Google Scholar