Effect of Postweld Heat Treatment on the Mechanical Properties of Weld in a Medium Carbon Steel

Abstract:

This paper presents the result of an investigation of the effect of postweld heat treatment on the mechanical properties of weld in 0.36%C medium Carbon Steel. Samples were prepared and welded using Shielded Metal Arc Welding (SMAW) process with a low hydrogen electrode. The welded samples were subjected to postweld heat treatment (stress relief) at four different temperatures: 550°C, 600°C, 650°C and 700°C followed by air-cooling. Microstructural examination was carried out to determine the change in microstructure before and after postweld heat treatment. The mechanical properties of the samples were also tested before and after the heat treatment. It was established that a hard microstructure, susceptible to Hydrogen Induced Cracking (HIC), was formed in the heat affected zone of the as-welded samples and that postweld heat treatment improved the mechanical properties of the weld and substantially reduced or eliminated the risk of HIC.

• Periodical: Applied Mechanics and Materials (Volume 315)
• Pages: 6-10
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.315.6
• Online since: April 2013
• Authors: S.M. Manladan, B.O. Onyekpe
• Keywords: Hardness, Martensite, Microstructure, Postweld Heat Treatment, Strength, Welding

References

[1] Wallace, J. F. A review of Welding Cast Steels and its Effects on Fatigue and Toughness Properties. Steel Founders' Society of America (1979).

[2] Parmar, R. S. Welding Engineering and Technology, 2nd Ed.: New Delhi, Khanna Publishers (2010). Pp 503-504.

[3] WTIA-Panel 1 – Guidance Note 6 Postweld Heat treatment (2003).

[4] Khan, M. D. Welding Science and Technology: New Delhi, New Age International (P) Limited, (2007). Pp2-5.

[5] ASM International Metals Handbook, Vol. 6- Welding, Brazing and Soldering: USA (1993).

[6] Desai, P. Monitoring Heat Treatment to Improve Weld Quality, Welding Journal-The American Welder (2010). Pp 109-111.

[7] Ahmed, K. and Krishnan, K. Post-Weld Heat Treatment – Case Studies. BARC Newsletter- Founder's Day Special Issue (2002).

[8] Funderbunk, R. S. Key concepts in welding Engineering-postweld heat treatment, Welding Innovation Vol. XV, No. 2 (1998). Pp 1-4.

[9] ASM International. Heat Treaters Guide: Practices and Procedures for Irons and Steels (1995). Pp 97-105.

[10] Oluwole, O. I., Omotoyinbo, J. A., and Damilola, A. A. The Effect of Weld Geometry and Post-Weld Heat Treatment on the Corrosion Behaviour of Austenitic Stainless Steel Immersed in 1. 0 M NaCl Solution. Materials Research vol 13 (1), (2010).

DOI: 10.1590/s1516-14392010000100006

[11] LANL Engineering Standards Manual ISD 341-2. GWS 1-08 – Post Weld Heat Treatment (2006).

[12] Callister, W. D. Materials Science and Engineering- An introduction: USA, John Wiley & Sons, Inc. (2007). Pp365-367.

[13] Welding Technology institute of Australia Hardness testing of welds (2006). Pp1-2.

[14] Bush, D., Brown, J., Lewis, K. An overview of NACE International Standard MR0103 and comparison with MR0175, Corrosion 2004, Paper No. 04649.

[15] ASM International. Metals Handbook, vol. 8-Mechanical Testing and Evaluation: USA, (1991). Pp 291-350.