Chips Shape in Case of Cutting Gears Using Flying Hobbing Cutter

Abstract:

This paper presents theoretical research related to the determination of the chips shape when milling gears using flying hobbing cutter. This specific type of tool is used in research the cutting process case of hobbing cutter, in order to minimize the cost of research. It is presented also the structure of the flying hobbing cutter used in own research. In the end, some conclusions related to gears cutting process in case of hobbing are underlined.

• Periodical: Applied Mechanics and Materials (Volume 772)
• Pages: 235-239
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.772.235
• Online since: July 2015
• Authors: Sorin Mihai Croitoru*, Cristina Mohora
• Keywords: Chips Shape, Cutting Gears, Flying Hobbing Cutter

References

[1] S. M. Croitoru, Cercetări privind danturarea cu scule din carburi metalice sinterizate integral, (Research on gear cutting with tools entirely made of metal carbides), PhD Thesis, POLITEHNICA University of Bucharest, (1998).

[2] K.D. Bouzakis, S. Kambogiannis, A. Antoniadis, N. Vidakis, Gear Hobbing Cutting Process and Tool Wear Prediction Models, in: Journal of Manufacturing Science and Engineering Transactions of the ASME, Vol. 124, February (2002).

DOI: 10.1115/1.1430236

[3] H.J. Ehmer, Beitrag zur Ermittlung der Gesetzmäβigkeiten und Ursachen des Freiflachenverschleiβes an Hartmetall-drehwerkzeugen, (Contributions to research of clearance face wear characteristic and reasons in case of turning using metal carbides tools), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1970).

[4] P. Gutmann, Zerspankraftberechnung beim Wälzfräsen, (Cutting force determination in gear hobbing), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1988).

[5] B. Hoffmeister, Űber den Verschleiβ am Wälzfräser, (Gear cutting with metal carbide hobbing cutter), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1970).

[6] W. Kőnig, J. Tondorf, K. Bouzakis, Possibilities to Avoid Built-up Edges in Gear Hobbing, Annals of the CIRP, Vol. 28/1/(1979).

[7] A. Mundt, Modell zur rechnerischen Standzeitbestimmung beim Wälzfräsen, (Model for computer calculus of hobbing cutter durability|), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1992).

[8] G. Sulzer, Leistungsteigerung bei der Zylinderradherstellung durch genaue Erfassung der Zerspankinematik, (Increase of cutting efficiency in cylindrical wheels gear cutting by means of accurate determination of cutting movements), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1973).

[9] G. Venohr, Beitrag zum Einsatz von Hartmetall – Werkzeugen beim Wälzfräsen, (Contributions to research of metal carbides tools in hobbing gears), PhD Thesis, Rheinisch-Westfalischen Technischen Hochschule Aachen, (1985).

[10] M. Weck, O. Hurasky-Schönwerth, W. Winter, Manufacturing Simulation for the Analysis of the Gear Hobbing Process, in: International Conference on Gears VDI-Berichte. l Nr. 1665, March (2002).