Characterisation of Plasticity Response for Reciprocating Sliding Wear Test of Ti-6Al-4V under Variables Number of Cycles

Abstract:

Article Preview

Reciprocating sliding wear test of uncoated titanium alloy, Ti-6Al-4V is investigated using pin-on-flat contact arrangement of Ti-6Al-4V/Ti-6Al-4V pair under variable number of cycles at low number of cycles. The worn surfaces of the titanium alloy specimens were analyzed with the use of optical microscope (2D and 3D OM) and Vickers Hardness analysis was carried on. The pattern of the wear scar characteristics determined and the finding at the end of wear track had been focus through the presence at the end of wear track. It is suggesting an evidence of plastic deformation with the increasing in hardness value. The increase in hardness value at the end of wear track indicates increase in the plastic deformation with increasing number of cycles.

Info:

Periodical:

Edited by:

Al Emran Ismail, Amir Khalid, Aziman Madun, Ahmad Kueh Beng Hong, Fariza Mohamad, Hamidon Salleh, Kamaruddin Ambak, Mohammad Kamil Abdullah, Mohd Azlis Sani Md Jalil, Mohd Ezree Abdullah, Mohd Fahrul Hassan, Mohd Halim Irwan Ibrahim et.al.

Pages:

168-172

Citation:

D. Harun et al., "Characterisation of Plasticity Response for Reciprocating Sliding Wear Test of Ti-6Al-4V under Variables Number of Cycles", Applied Mechanics and Materials, Vols. 773-774, pp. 168-172, 2015

Online since:

July 2015

Export:

[1] S. R. Chauhan, K. Dass, Dry Sliding Wear Behaviour of Titanium (Grade 5) Alloy by Using Response Surface Methodology, Advanved In Tribology, Hindawi Publishing Corp., India, 2013, p.9.

DOI: https://doi.org/10.1155/2013/272106

[2] L. Faure, B. Bolle, S. Philippon, C. Schuman, P. Chevrier, A. Tidu, Friction Experiments for titanium alloy tribopairs sliding in dry conditions: Sub-surface and surface analysis, Tribol. Int., 54 (2012) 17–25.

DOI: https://doi.org/10.1016/j.triboint.2012.04.007

[3] A. Molinari, G. Straffelini, B. Tesi, T. Bacci, Dry sliding wear mechanisms of the Ti6Al4V alloy, Wear, 208 (1997)105–112.

DOI: https://doi.org/10.1016/s0043-1648(96)07454-6

[4] R. S. Magaziner, V. K. Jain, S. Mall, Wear characterization of Ti-6Al-4V under fretting-reciprocating sliding conditions. Wear, 264 (2008) 1002–1014.

DOI: https://doi.org/10.1016/j.wear.2007.08.004

[5] A. Kapoor, F. J. Franklin, Tribological layers and the wear of ductile materials. Wear, 245 (2000) 204–215.

DOI: https://doi.org/10.1016/s0043-1648(00)00480-4

[6] A. L. M. Tobi, J. Ding, G. Bandak, S. B. Leen, P. H. Shipway, A study on the interaction between fretting wear and cyclic plasticity for Ti – 6Al – 4V. Wear, 267 (2009) 270–282.

DOI: https://doi.org/10.1016/j.wear.2008.12.039

[7] D. Harun, A. L. M. Tobi, A. Singh Chaal, and R. Md. Nasir, "Characterisation of plasticity response for reciprocating sliding wear test of Ti-6Al-4V under variables normal load. Presented in ICXRI Conference, JB, 11-13 Ogos (2014).

DOI: https://doi.org/10.4028/www.scientific.net/amr.1087.350

[8] E. O. Ezugwu, Z. M. Wang, Materials Titanium alloys and their machinability, Journal of Materials Processing Technology, 68 (1997) 262–274.

[9] Y. Luo, L. Yang, and M. Tian, Influence of Bio-Lubricants on the Tribological Properties of Ti6Al4V Alloy, J. Bionic Eng., vol. 10, no. 1, p.84–89, Jan. (2013).

DOI: https://doi.org/10.1016/s1672-6529(13)60202-4

[10] Y. Chen, T. Cheng, and X. Nie, Wear failure behaviour of titanium-based oxide coatings on a titanium alloy under impact and sliding forces, J. Alloys Compd., vol. 578, p.336–344, (2013).

DOI: https://doi.org/10.1016/j.jallcom.2013.05.199

[11] Y. Luo, L. Yang, and M. Tian, Influence of Bio-Lubricants on the Tribological Properties of Ti6Al4V Alloy, J. Bionic Eng., vol. 10, no. 1, p.84–89, Jan. (2013).

DOI: https://doi.org/10.1016/s1672-6529(13)60202-4

[12] K. L. Johnson, Contact mechanics and the wear of metal, Wear, vol. 190, p.162–170, (1995).

[13] A. L. M. Tobi, J. Ding, G. Bandak, S. B. Leen, and P. H. Shipway, A study on the interaction between fretting wear and cyclic plasticity for Ti – 6Al – 4V, Wear, vol. 267, p.270–282, (2009).

DOI: https://doi.org/10.1016/j.wear.2008.12.039

[14] R. S. Magaziner, V. K. Jain, and S. Mall, Wear characterization of Ti-6Al-4V under fretting-reciprocating sliding conditions, Wear, vol. 264, no. 11–12, p.1002–1014, May (2008).

DOI: https://doi.org/10.1016/j.wear.2007.08.004

[15] M. Mieaniqur-phyriquc, S. Fouvry, P. Kapsa, H. Zahouani, and L. E. O. Vincent, Wear analysis in fretting of hard coatings through a dissipated energy concept, Wear, vol. 1648, no. 96, (1997).

DOI: https://doi.org/10.1016/s0043-1648(96)07436-4

[16] N. M. Everitt, J. Ding, G. Bandak, P. H. Shipway, S. B. Leen, and E. J. Williams, Characterisation of fretting-induced wear debris for Ti-6Al-4 V, Wear, vol. 267, no. 1–4, p.283–291, Jun. (2009).

DOI: https://doi.org/10.1016/j.wear.2008.12.032