Impact of Tool Inserts in High Speed Machining of GFRP Composite Material

K. Anand; M.V. Siddharth; K.S. Vijay Sekar; S. Suresh Kumar

doi:10.4028/www.scientific.net/AMM.787.664

Paper Titles

Tool Wear Analysis of Al 6061 Reinforced with 10 wt% Al₂O₃ Using High Hardened Inserts
p.643

Influence of Particle Feeding Methods on Processing the AA6061/SiC Metal Matrix Nanocomposites
p.648

Tribological Characteristics of Al6061-TiC Composite Synthesized by In Situ Technique
p.653

Effects of Red Mud Reinforcement on Hardness, Wear Behaviour of Cast Al-6Si-0.45 Mg Alloy
p.658

Impact of Tool Inserts in High Speed Machining of GFRP Composite Material
p.664

Friction Stir Welding of the Aluminum Matrix Composite - A Literature Review
p.669

Experimental Analysis of Different Packed Bed Catalysts for Lean NOx Traps (LNT)
p.677

Spray Characteristics of Diesel and Biodiesel Fuels for Various Injection Timings under Non Evaporating Conditions
p.682

Experimental Studies on the Performance of C.I Engine with Fish Oil Methyl Ester as Fuel for Various Blends of Diesel and LPG
p.687

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 787Impact of Tool Inserts in High Speed Machining of...

Impact of Tool Inserts in High Speed Machining of GFRP Composite Material

Abstract:

Composite materials are in-homogenous, anisotropic and cause high tool wear at high cutting speeds in machining. Industrial practices worldwide reveal a need to use high speed machining to achieve the desired material removal rate, surface finish and to reduce cost cutting. In this research work, impact of turning glass fibre reinforced polymer tube with two contrasting turning tool inserts such as titanium aluminium nitride and tungsten carbide have been analysed. The turning was conducted at low to high cutting conditions up to spindle speeds of 2000 rpm and feed rate of 0.446mm/rev. The cutting force, feed force were acquired with a strain gauge based dynamometer, the chip cross section was observed using scanning electron microscopy and the temperature was sensed with a infra red thermo sensor. The advanced titanium aluminium nitride insert shows better machining characteristics across cutting speeds.

You might also be interested in these eBooks

Alternative Energy Sources, Materials and Technologies

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 787)

Pages:

664-668

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.787.664

Citation:

Cite this paper

Online since:

August 2015

Authors:

K. Anand*, M.V. Siddharth, K.S. Vijay Sekar, S. Suresh Kumar

Keywords:

Cutting Forces, GFRP, High Speed Turning, Temperature, Tool Inserts

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Syed Altaf Hussain,V. Pandurangadu,K. Palani Kumar: Machinability of glass fiber reinforced plastic (GFRP) composite materials, Int.J. Eng. Sci. Technol. 3(2011) 103-118.

DOI: 10.4314/ijest.v3i4.68546

Google Scholar

[2] Surinder Kumar, Meenu, Ps. Satsangi, HK. Sardana: Optimization of surface roughness in turning unidirectional glass fiber reinforced plastics (UD-GFRP) composites using polycrystalline diamond (PCD) cutting tool. Indian.J. Eng. Mater. Sci . 19(2012).

DOI: 10.4314/ijest.v4i2.8

Google Scholar

[3] K. Palanikumar,J. Paulo Davim: Assessment of some factors influencing tool wear on the machining of glass fibre-reinforced plastics by coated cemented carbide tools. J. Mater. Process. Technol. 209 (2009)511–519.

DOI: 10.1016/j.jmatprotec.2008.02.020

Google Scholar

[4] Chinmaya R. Dandekar and Yung C. Shin: Modelling of machining of composite materials: A review, Int J Mach Tool Manu. 57. (2012)102-121.

Google Scholar

[5] Chung-Shin Chang: Turning of glass–fiber reinforced plastics materials with chamfered main cutting edge carbide tools. J. Mater. Process. Technol. 180 (2006)117–129.

DOI: 10.1016/j.jmatprotec.2006.05.011

Google Scholar

[6] Meenua and Surinder Kumar: Prediction of Surface Roughness in Turning of UD-GFRP by using Artificial Neural Network. Mech Confab. 2 (2013).

Google Scholar

[7] Surinder Kumar GILL, Meenu Gupta, P. S. Satsanghi: Prediction of cutting forces in machining of unidirectional glass fiber reinforced plastics composite. J. Mech. Eng. (2013)187–200.

DOI: 10.1007/s11465-013-0262-x

Google Scholar

[8] T. Rajasekaran, K. Palanikumar, B.K. Vinayagam: Turning CFRP composites ceramic tool for surface roughness. J. pro. eng. 38(2012)2922-2929.

DOI: 10.1016/j.proeng.2012.06.341

Google Scholar

[9] M. Adham khan,A. Senthil kumar: Machinability of glass fibre reinforced plastic (GFRP) composite using alumina-based ceramic cutting tools. J. Manu. Processes. 13(2011)67–73.

DOI: 10.1016/j.jmapro.2010.10.002

Google Scholar

[10] K. Palanikumar,J. Paulo Davim: Assessment of factors influencing surface roughness on the machining of glass fiber-reinforced polymer composites. Mater. Des. 27 (2006)862-871.

DOI: 10.1016/j.matdes.2005.03.011

Google Scholar