Study on the Cutting Temperature and Chips Formation during the Milling of Pure Titanium

Abstract:

In this paper some experimental determinations on the temperature during the milling process of pure titanium is conducted, using different cutting conditions. The results are presented as graphical dependencies and also as a screen capture of the values obtained using an adequate technique for temperature of the cutting process. Some pictures of the chips shape captured during milling process of the pure titanium bare are presented.

• Periodical: Applied Mechanics and Materials (Volume 880)
• Pages: 315-320
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.880.315
• Online since: March 2018
• Authors: Emil Nicusor Patru, Dumitru Panduru, Nicolae Craciunoiu*, Marin Bica
• Keywords: Chips, Cutting Temperature, Milling, Titanium

References

[1] A. Pramanik, G. Littlefair, Machining of titanium alloy (Ti-6Al-4V) - Theory to application, Machining Science and Technology, Vol. 19, 2015, Issue 1, pag. 1-49.

DOI: 10.1080/10910344.2014.991031

[2] Yong Yang, Weiwei Zhu, Study on cutting temperature during milling of titanium alloy based on FEM and experiment, Int. J. Adv. Manuf. Technol. (2014) 73: 1511–1521.

DOI: 10.1007/s00170-014-5937-x

[3] D. Carou, E.M. Rubio and J.P. Davim, Discontinuous cutting: failure mechanisms, tool materials and temperature, Rev. Adv. Mater. Sci. 38 (2014) 110-124.

[4] V Krishnaraj, S Samsudeensadham, R Sindhumathi , P Kuppan, A study on high speed end milling of titanium alloy, Procedia Engineering 97 ( 2014 ) 251 – 257.

DOI: 10.1016/j.proeng.2014.12.248

[5] Józef Kuczmaszewski, Ireneusz Zagórski, Methodological problems of temperature measurement in the cutting area during milling magnesium alloys, Management and Production Engineering Review, Volume 4, Number 3, September 2013, p.26–33.

DOI: 10.2478/mper-2013-0025

[6] Rui Li, Albert J. Shih, Tool Temperature in Titanium Drilling, Transactions of the ASME, Vol. 129, August 2007, pp.740-749.

[7] Muhammad, R., et al,. Effect of cutting conditions on temperature generated in drilling process: A FEA approach. Advanced Materials Research, 2011, 223, pp.240-246.

DOI: 10.4028/www.scientific.net/amr.223.240

[8] Seyed Ali Niknam, Raid Khettabi and Victor Songmene, Machinability and Machining of Titanium Alloys: A Review, Chapter 1, in J. P. Davim (ed. ), Machining of Titanium Alloys, Materials Forming, Machining and Tribology, DOI: 10. 1007/978-3-662-43902-9_1, Springer-Verlag Berlin Heidelberg (2014).

DOI: 10.1007/978-3-662-43902-9_1

[9] G.M. Pittala, M. Monno, A new approach to the prediction of temperature of the workpiece of face milling operations of Ti-6Al-4V, Applied Thermal Engineering, Elsevier, 2010, 31(2-3) p.173.

DOI: 10.1016/j.applthermaleng.2010.08.027

[10] Patil Amit S., Nashik, Ingle Sushil V., More Yogesh S., Nathe Manik S., Machining Challenges in Ti-6Al-4V. -A Review, International Journal of Innovations in Engineering and Technology (IJIET), Volume 5 Issue 4 August 2015, p.6 – 23.

[11] Valery Marinov, Manufacturing Technology, Chapter Cutting temperature, pp.74-76.

[12] F.G. Ciolacu, N. Craciunoiu, Teoria aschierii (in Romanian), Editura Universitaria, Craiova, (2014).