Low Frequency Mechanical Spectroscopy of High Damping Mg-3wt.%Ni Alloy

Di Qing Wan; Ya Juan Liu

doi:10.4028/www.scientific.net/AMR.146-147.1761

Paper Titles

Finite Element Simulation of Die Design for Equal Channel Angular Extrusion Process of Pure Aluminum and its Experimental Investigation
p.1737

Corrosion Behaviour of a Fe-Based Alloy in Zn and Zn-55Al Baths
p.1741

The Effect of Minimal Quantity Lubrication (MQL) on the Surface Roughness of Titanium Alloy Ti-6Al-4V ELI in Turning Process
p.1750

Preparation and Photoactivity of Titanium Dioxide-Coated Carbon Felt Using Supercritical Carbon Dioxide
p.1754

Low Frequency Mechanical Spectroscopy of High Damping Mg-3wt.%Ni Alloy
p.1761

Icosahedral Quasicrystal Grains Growth and Evolution in Mg-Zn-Y
p.1765

Macroscopic and Mesoscopic Large Deformation Measurement Methods for Metal Materials
p.1769

In Situ Mg₂Si Reinforced Mg Alloy Synthesized in Mg-SiO₂ System
p.1775

Very High Cycle Fatigue Behavior of Carbon Manganese Steels
p.1780

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 146-147Low Frequency Mechanical Spectroscopy of High...

Low Frequency Mechanical Spectroscopy of High Damping Mg-3wt.%Ni Alloy

Abstract:

The Dynamic Mechanical Analysis (DMA) was applied to investigate the low frequency mechanical spectroscopy response of as-cast high damping Mg-3wt.%Ni hypoeutectic alloys. There are two peaks appearing on the temperature dependent damping spectrum (-100 - 420 °C). The broad peak P1 is overlapped by some small peaks due to the thermally activated dislocation movement, while the P2 peak is a solute grain boundary relaxation peak.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 146-147)

Pages:

1761-1764

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.146-147.1761

Citation:

Cite this paper

Online since:

October 2010

Authors:

Di Qing Wan, Ya Juan Liu

Keywords:

Damping Mechanisms, Damping Peak, Mechanical Spectroscopy, Mg-3wt.%Ni Alloy

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] R, A. M. Mato Rubhera, T. S. Mufuruki, Transp. Res. Part D: Trans. Environ. Vol. 4(1999), p.81.

Google Scholar

[2] M. M. Avedesian, H. Baker (Eds. ), ASM Specialty Handbook, Magnesium and Magnesium Alloys, ASM International, The Materials Information Society, Ohio, (1999).

Google Scholar

[3] K. Sugimoto, K. Niiya, T. Okamoto, K. Kishitake, Trans JIM, Vol. 18(1977), p.277.

Google Scholar

[4] X.S. Hu, Y.K. Zhang, M.Y. Zheng, K. Wu, Scr. Mater., Vol. 52 (2005), p.1141.

Google Scholar

[5] O.A. Lambri, W. Riehemann, E.J. Lucioni, R.E. Bolmaro, Mater. Sci. Eng. A, Vol. 442(2006), p.476.

Google Scholar

[6] J. Zhang, R. J. Perez, C. R. Wong, Mater. Sci. Eng. R, Vol. 13(1994), p.325.

Google Scholar

[7] A. Granato, K. Lücke, J. Appl. Phys., Vol. 27(1956), p.583.

Google Scholar

[8] A. Granato , K. Lücke, J. Appl. Phys., Vol. 27(1956), p.789.

Google Scholar

[9] G. Fantozzi, C. Esnouf, W. Benoit, I. G. Ritchie, Prog. Mater. Sci., Vol. 27(1982), p.311.

Google Scholar

[10] H. Strunk, R. Frydman, Mater. Sci. Eng., Vol. 18(1975), p.143.

Google Scholar