Study of Force Measurement in Honing

Abstract:

Honing is an abrasive machining process that produces a precision surface on a workpiece and widely used in manufacturing engine cylinder walls, compressor bodies, valve bodies, bearings, hydraulic cylinders and so on. Investigation and acquisition of the honing force could be used to investigate the honing mechanism and optimize the processing parameter. But it is difficult to measure the force during the honing process because of the limited honing structure. This paper presents a measuring system for honing force. It introduces the measure theory and the measure system. The whole measuring system is validated by experiment.

• Periodical: Advanced Materials Research (Volumes 314-316)
• Pages: 2381-2384
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.314-316.2381
• Online since: August 2011
• Authors: Yun Xia Hou, Qian Wang, Qiang Feng, Cheng Zu Ren
• Keywords: Force, Honing, Measurement

References

[1] Lee, J.; Malkin, S. (1993) Experimental investigation of the bore honing process. Transactions of the ASME, 115(4): 406-414.

DOI: 10.1115/1.2901783

[2] Borkowski, J. A.; Szymański, A. M. (1992) Uses of abrasives and abrasive tools. Ellis Horwood, New York, USA.

[3] Hou, Z. B.; Komanduri, R. (2003) On the mechanics of the grinding process - Part I. Stochastic nature of the grinding process. International Journal of Machine Tools and Manufacture, 43(15): 1579-1593.

DOI: 10.1016/s0890-6955(03)00186-x

[4] Bardac, D.; Marinescu, I. D. (1999) Surface generation in the case of honing with superabrasives. Society of Manufacturing Engineers, MR99-240: 1-7.

[5] Gouskov, A.M.; Voronov, S.A.; Batzer, S.A. (2001) Dynamic stability of rotating abrasive tool for deep hole honing. Proceedings of the ASME Design Engineering Technical Conference, 6 B: 1133-1139.

DOI: 10.1115/detc2001/vib-21436

[6] Gouskov, A.M.; Voronov, S.A.; Butcher, E.A, Sinha S.C. (2003) Influence of honing dynamics on surface formation. Proceedings of the ASME Design Engineering Technical Conference, 5 C: 2239-2245.

[7] Gouskov, A. M.; Butcher, E. A.; Voronov, S. A.; Sinha, S. C. (2004) Simulation of machined surface formation while honing, American Society of Mechanical Engineers. Manufacturing Engineering Division, 15: 947-95

DOI: 10.1115/imece2004-59268

[8] Voronov, S. A. (2008) Effect of dynamics on the process of formation of holes during honing. Journal of Machinery Manufacture and Reliability, 37(3): 270-277.

DOI: 10.3103/s1052618808030114

[9] Kishawy, H. A.; Haglund, A. J.; Deiab, I. M. (2006) An analysis of machining with honed tools using ale finite element model Ploughing force and minimum chip thickness. Transactions of the North American Manufacturing Research Institute of SME, 34: 277-284.

[10] Wang, F.; Keer, L. M.; Wang, Q. J. (2006) Numerical simulation and analysis for 3D elastic-plastic rough contacts. American Society of Mechanical Engineers, Tribology Division, TRIB, 10.

DOI: 10.1115/imece2006-14663

[11] Cristea, R.; Neagu, C.; Dumitrescu, A.; Bayer, M. (1998) Machinability functions in cast-iron honing with diamond tools. UPB Scientific Bulletin, Series D Mechanical Engineering, 60(3): 381-388.

[12] Kim, J.D.; Choi, M.S. (1997) Study on the prediction of roundness variation in honing using hone dynamics. Journal of Testing & Evaluation, 25(6): 556-564.

DOI: 10.1520/jte11495j

[13] Neagu, C.; Cristea, R.; Dumitrescu A., Bayer, M. (1998) Cutting parameter optimization in cast-iron honing with diamond tools. UPB Scientific Bulletin, Series D Mechanical Engineering, 60(3): 349-355.