The Effects of Heat Treatment and Cold Working on the Microstructure of Aluminum Alloys Welded by Friction Stir Welding (FSW) Technique

Abstract:

The application of hot deformation during Friction Stir Welding (FSW) gives rise to produce a weld nugget consisting usually of dynamically recrystallized grains whose size is substantially lower than that of the base material. In the present study, several specimens with different conditions were first prepared using 2024 and 5083 aluminum alloys, which were then welded with FSW method. The microstructures of weld nugget in both series of specimens were examined using optical and scanning electron microscopes. The specimen of 2024 with anneal (O) and artificial aging (T6) conditions, and type 5083 with anneal (O), 30% and 50% cold work conditions were friction stir welded. Grain size distribution, hardness and temperature profiles in the welded zones were determined in order to obtain the relationship between the grain structure and the hardness profile in these regions. In each alloy, the average grain size in the weld nuggets was identical. The hardness of nugget zones in each alloy was the same due to their similar microstructures. According to the results obtained in this investigation, the initial microstructure showed no considerable effect on final microstructure and hardness of the weld nuggets, which this effect may be attributed to continuous dynamic recrystallization phenomenon.

• Periodical: Advanced Materials Research (Volume 409)
• Pages: 287-292
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.409.287
• Online since: November 2011
• Authors: M. Mohammadtaheri, M. Haddad-Sabzevar, Mohammad Mazinani
• Keywords: Aluminum (Al), Friction Stir Welding (FSW), Hardness, Microstructure, Recrystallization

References

[1] H. Aydin, A. Bayrama, A. Uguz, K.S. Akay, Tensile properties of friction stir welded joints of 2024 aluminum alloys in different heat-treated-state, Materials and Design, Vol. 30, p.2009, 2211–2221.

DOI: 10.1016/j.matdes.2008.08.034

[2] R.S. Mishraa, Z.Y. Ma, Friction stir welding and processing, Materials Science and Engineering A, Vol. 50, 2005, pp.1-78.

[3] P.L. Threadgill, A.J. Leonard, H.R. Shercliff and P.J. Withers, Friction stir welding of aluminium alloys, International Materials Reviews, Vol. 54, No. 2, (2009).

DOI: 10.1179/174328009x411136

[4] M.J. Jones , P. Heurtier, C. Desrayaud, F. Montheillet, D. Allehaux , J.H. Driver, Correlation between microstructure and microhardness in a friction stir welded 2024 aluminum alloy, Scripta Materialia, Vol. 52, 2005, pp.693-697.

DOI: 10.1016/j.scriptamat.2004.12.027

[5] K. Elangovana, V. Balasubramanian, Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminum alloy, Journal of Materials Processing Technology, Vol. 200, 2008, p.163–175.

DOI: 10.1016/j.jmatprotec.2007.09.019

[6] D.M. Rodrigues, A. Loureiro , C. Leitao , R.M. Leal, B.M. Chaparro, P. Vilaça, Influence of friction stir welding parameters on the microstructural and mechanical properties of AA 6016-T4 thin welds, Materials and Design, Vol. 30, 2009, p.1913–(1921).

DOI: 10.1016/j.matdes.2008.09.016

[7] X. Cao , M. Jahazi, Effect of welding speed on the quality of friction stir welded butt joints of a magnesium alloy, Materials and Design, Vol. 30, 2009, p.2033–(2042).

DOI: 10.1016/j.matdes.2008.08.040

[8] T. Saeid, A. Abdollah-zadeh, H. Assadi, F. Malek Ghaini, Effect of friction stir welding speed on the microstructure and mechanical properties of a duplex stainless steel, Materials Science and Engineering A, Vol. 496, 2008, p.262–268.

DOI: 10.1016/j.msea.2008.05.025

[9] Jian-Qing Su, T.W. Nelson, C.J. Sterling, Microstructure evolution during FSW/FSP of high strength aluminum alloys, Materials Science and Engineering A, Vol. 405, 2005, p.277–286.

DOI: 10.1016/j.msea.2005.06.009

[10] X. Sauvage, A. D´ed´e, A.C. Mu˜noz, B. Huneau, Precipitate stability and recrystallization in the weld nuggets of friction stir welded Al–Mg–Si and Al–Mg–Sc alloys, Materials Science and Engineering A, Vol. 491, 2008, p.364–371.

DOI: 10.1016/j.msea.2008.02.006

[11] P.B. Prangnell, C.P. Heason, Grain structure formation during friction stir welding observed by the stop action technique, Acta Materialia, Vol. 53, 2005, p.3179–3192.

DOI: 10.1016/j.actamat.2005.03.044