Reduction in Defect Rate by Taguchi Method in Plastic Injection Molded Components

Abstract:

In the present era, competition gets tougher; there is more pressure on manufacturing sectors to improve quality and customer satisfaction while decreasing cost and increasing productivity. These can be achieved by using modern quality management systems and process improvement techniques to reduce the process variability and driven waste within manufacturing process using effective application of statistical tools. Taguchi technique is well known technique to solve industrial problems. This technique is fast and can pinpoint the chief causes and variations. Plastic injection molding is suitable for mass production articles since complex geometries can be obtained in a single production step. The difficulty in setting optimal process conditions may cause defects in parts, such as shrinkage and warpage. In this paper, optimal injection molding conditions for minimum shrinkage were determined by the Taguchi design of experiment (DOE) approach. Polypropylene (PP) was injected in circular shaped specimens under various processing parameters: melt temperature, injection pressure, packing pressure and packing time. S/N ratios were utilized for determining the optimal set of parameters. According to the results, 2400 C of melt temperature, 75 MPa of injection pressure, 50 MPa of packing pressure and 15 sec. of packing time gave minimum shrinkage of 0.951% for PP. Statically the most significant parameter was melt temperature for the PP. Injection pressure had the least effect on the shrinkage. The defect rate was reduced from 14% to 3%.

• Periodical: Advanced Materials Research (Volumes 488-489)
• Pages: 269-273
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.488-489.269
• Online since: March 2012
• Authors: G.S. Dangayach, Deepak Kumar
• Keywords: Design of Experiment (DOE), Packing Pressure, Packing Time, Plastic Injection Molding, Shrinkage, Taguchi Method

References

[1] M. Alton. Reducing shrinkage in injection moldings via the Taguchi, ANOVA and Neural Network Methods. Journals of Materials and Designs- 2010, 31: 599-604.

DOI: 10.1016/j.matdes.2009.06.049

[2] J. Antony. Pros and cons of six sigma: an academic perspective. Retrieved Quality Engineering- (2008).

[3] O. Hasan, E. Tuncay, and U. Ibrahim. Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part. Journal of Materials & Design- 2007, 28: 1271-1278.

DOI: 10.1016/j.matdes.2005.12.013

[4] J. A. De Feo, and B. William. Juran Institute's Six Sigma Breakthrough and Beyond- Quality Performance Breakthrough Methods. McGraw –Hill Professional. New York, Ny, ISBN 0071422277, (2005).

[5] H. X. Huang, Y.Z. Li, and Y.H. Deng. On-line real-time acquisition for transient temperature in blow molding. Polymer Test- 2006, 25: 839–845.

DOI: 10.1016/j.polymertesting.2006.04.003

[6] O. Vaatainen, and J. Pentti. Effect of processing parameters on the quality of injection molded parts by using the Taguchi parameter design method. Plast. Rubber Compos- 1994, 21: 211–217.

[7] C. Shen, L. Wang, and Q. Li. Optimization of injection molding process parameters using combination of artificial neural network and genetic algorithm method. Journal of Material Process Technology- 2007, 183(2–3): 412–428.

DOI: 10.1016/j.jmatprotec.2006.10.036

[8] S. J. Liao, W. H. Hsieh, J. T. Wang, and Yc. Su. Shrinkage and warpage prediction of injection molded thin wall parts using artificial neural network. Polymer Engg. Science- 2004, 44 (11): 2029-40.

DOI: 10.1002/pen.20206

[9] C. C. Chiu, C. T. Su, G. H. Yang, J. S. Huang, S. C. Chen, and N. T. Chen. Selection of optimal parameters in gas assisted injection molding using a neural network model and the Taguchi method. International Journal of Quality Science- 1997, 2: 106–120.

DOI: 10.1108/13598539710167096