Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts under Room Temperature Conditions

Abstract:

Inconel 718 is used for high-temperature applications in aerospace, nuclear, and automotive industries due to its resistance, at high temperatures, to corrosion, fatigue, creep, oxidation, and deformation. Unfortunately, these same qualities also impair its machinability and researchers have investigated on ways to machine it economically. Some unconventional machining practices such as: Plasma Enhanced and Laser Assisted Machining etc. have been applied. However these practices increase the machining cost. This research investigated the viability of high speed end milling of Inconel 718 using circular Silicon Nitride (ceramic) inserts under room temperature conditions. Tool wear (flank and notch wear), machining vibration amplitude and average surface roughness were evaluated for the feasibility analysis. A vertical CNC mill was used to machine Inconel 718 samples using different combinations of three primary machining parameters: cutting speed, feed, and depth of cut. Vibration data acquisition device and Datalog DasyLab 5.6 software were used to analyze machining vibration. Scanning Electron Microscope (SEM) and surface profilometer were utilized to measure tool (flank and notch) wear and surface roughness, respectively. It was observed that the machining vibrations, in high speed machining, was reasonable (0.045 V on the average). This resulted in acceptable tool wear (averages: flank wear = 0.25 mm, notch wear = 0.45 mm) and semi-finished surface roughness (0.30 µm) measured after every 30 mm length of cut. Thus, room temperature high speed machining of Inconel 718 using circular silicon nitride inserts is a practical option.

• Periodical: Advanced Materials Research (Volumes 538-541)
• Pages: 1351-1355
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.538-541.1351
• Online since: June 2012
• Authors: A.K.M. Nurul Amin, Suhaily Mokhtar, Muammer Din Arif
• Keywords: Ceramic Insert, Hard Machining, High Speed End Milling, Inconel 718, Room Temperature Machining, Surface Roughness (SR), Tool Wear

References

[1] Engelmore, A. Gatt and L. Iulliano: Chip Formation Analysis in High Speed Machining of a Nickel Base Superalloy with Silicon Carbide Whisker-Reinforced Alumina, Int. J. Mach. Tools Manufac. Vol. 34, No. 8 (1994), pp.1147-1161.

DOI: 10.1016/0890-6955(94)90019-1

[2] E. O. Ezugwu: Key Improvements in the Machining of Difficult to Cut Aerospace Superalloys, Int. J. Mach. Tools Manufac. Vol. 45 (2005), pp.1353-1367.

DOI: 10.1016/j.ijmachtools.2005.02.003

[3] L. Li, N. He, M. Wang and Z. G. Wng: High Speed Cutting of Inconel 718 with Coated Carbide and Ceramic Inserts, J. of Materials Processing Technol. Vol. 129 (2002), pp.127-130.

DOI: 10.1016/s0924-0136(02)00590-3

[4] M. B. Silva and J. Wallbank: A Review–Cutting Temperature: Prediction and Measurement Methods, Int. J. of Materials Processing Technol. Vol. 88, pp.127-130.

[5] M. Alauddin, M. A. El-Baradie and S. J. Hashmi: Tool Life Testing in the End Milling of Inconel 718, J. of Materials Processing Technol. Vol. 55, pp.321-330.

DOI: 10.1016/0924-0136(95)02035-7

[6] S. Kim: Material Properties of Ceramic Cutting Tools, Key Engineering Materials (Trans Tech. Publications, Switzerland), Vol. 96 pp.33-80.

[7] L. Li, N. Wang and M. Wang: High Speed Cutting of Inconel 718 with Coated Carbide and Ceramic Inserts, J. of Materials Processing Technol. Vol. 129 (2002), pp.127-130.

DOI: 10.1016/s0924-0136(02)00590-3

[8] R. M. Arunachalam, M. A. Mannan and A. C. Spowage: Residual Stress and Surface Roughness When Facing Age Hardened Inconel 718 with CBN and Ceramic Cutting Tools, Int. J. of Machine Tools and Manufac. Vol. 44, pp.879-887.

DOI: 10.1016/j.ijmachtools.2004.02.016

[9] S. Kalpakjian: Manufacturing Processes for Engineering Materials, Addison-Wesley, 489.

[10] H. Z. Li, H. Zeng and X. Q. Chen: An Experimental Study of Tool Wear and Cutting Force Variation in the End Milling of Inconel 718 with Coated Carbide Inserts, J. of Materials Processing Technol. Vol. 180, pp.296-304.

DOI: 10.1016/j.jmatprotec.2006.07.009

[11] E. O. Ezugwu and I. R. Pashby: High Speed Milling of Nickel Based Superalloys, J. of Materials Processing Technol. Vol. 33, pp.429-437.

DOI: 10.1016/0924-0136(92)90277-y

[12] N. Narutaki, Y. Yamane, K. Hayashi and T. Kitagawa: High Speed Machining of Inconel 718 with Ceramic Tools, Annals of CIRP Vol. 42, pp.103-106.

DOI: 10.1016/s0007-8506(07)62402-0

[13] M. E. R. Bonifacio and A. E. Diniz: Correlating Tool Wear, Tool Life, Surface Roughness and Vibration in Finish Turning with Coated Carbide Tools, Wear, Vol. 173 (1994) pp.137-144.

DOI: 10.1016/0043-1648(94)90266-6

[14] G, Germain, J. L. Lebrun, T. Braham-Bouchnak, D. Belet and S. Auger: Laser-Assisted Machining of Inconel 718 with Carbide and Ceramic Inserts, Int. J. Material Forming, suppl. 1 pp.523-526.

DOI: 10.1007/s12289-008-0213-y

[15] E. L. Carl, J. N. Kim and Y. C. Shin: Laser-Assisted Machining of Inconel 718 with Carbide and Ceramic Inserts. Int. J. of Machine Tools and Manufac. Vol. 41 (2001) pp.877-897.