Investigations on the Effect of Tool Speed and Feed Rate on the Friction Stir Processed AZ31B Magnesium Alloys

D. Peter Pushpanathan; K. Ganesa Balamurugan; K. Mahadevan

doi:10.4028/www.scientific.net/AMR.622-623.700

Paper Titles

Preparation and Gas Sensing Properties of 2,9,16,23-Tetra-Tert-Butyl-29H, 31H- Copper (II) Phthalocyanine LB Thin Films
p.679

Heredity of the Structure and Properties of Grey Cast Iron Melted on a Basis of Steel Scrap
p.685

High Temperature Performance of TiAlON Thin Films
p.690

Tailoring the Hysteresis Loop of the Si/Cu(10nm)/FeMn(10-30nm)/CoFeB(10nm) Bilayer System
p.695

Investigations on the Effect of Tool Speed and Feed Rate on the Friction Stir Processed AZ31B Magnesium Alloys
p.700

Effect of Process Parameters on Microstructure and Mechanical Properties on Severe Plastic Deformation Process of Aa7075-T6 Aluminum Alloy
p.705

Comparison of Bubble Electrospinning and Needle Electrospinning of Ethylcellulose Ultrafine Fibres
p.710

Stress Induced in Al₂O₃ Films as Deposited onto Al₂O₃TiC Substrate by RF Diode Sputtering
p.716

Hydrogen Integration in Refinery Using MINLP Method
p.720

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 622-623Investigations on the Effect of Tool Speed and...

Investigations on the Effect of Tool Speed and Feed Rate on the Friction Stir Processed AZ31B Magnesium Alloys

Abstract:

The friction stir processing is a solid state processing technique. The present study investigates the effect of process parameters like tool rotational speed and tool feed on the mechanical and tribological properties of friction stir processed AZ31B magnesium alloy. The experiments were conducted with 3 level 2 factors full factorial design with two replications. The responses were tensile strength, microhardness and wear. The investigation reveals that both the tensile strength and microhardness values were decreasing with decreasing grain size. The minimum wear rates were observed at higher hardness values.

You might also be interested in these eBooks

Manufacturing Science and Technology III

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 622-623)

Pages:

700-704

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.622-623.700

Citation:

Cite this paper

Online since:

December 2012

Authors:

D. Peter Pushpanathan, K. Ganesa Balamurugan, K. Mahadevan

Keywords:

ANOVA, AZ31B Alloy, FSP, Wear

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Yu Sirong, Chen Xianjun, Huang Zhiqiu, Liu Yaohui: Journal of rare earths, Vol. 28, No. 2, (2010), p.316.

Google Scholar

[2] Mordike B L, Ebert T: Materials Science and Engineering A (2001) Vol. 302, p.37.

Google Scholar

[3] Kinji Hirai, Hidetoshi Somekawa, Yorinobu Takigawa, Kenji Higashi: Materials Science and Engineering A (2005), Vol. 403, p.276.

Google Scholar

[4] Parviz Asadi & Ghader Faraji & Mohammad K. Besharati: Int J Adv Manuf Technol (2010) Vol. 51, p.247.

Google Scholar

[5] Morisada Y, Fujji H, Nagaoka T, Fukusumi M: mater. Sci Eng A (2006) Vol. 433, p.50.

Google Scholar

[6] Darras BM, Khraisheh MK, Abu-Farha FK, Omar MA: Mater Proc Tech (2007) Vol. 191, p.77.

Google Scholar

[7] P. Cavaliere, P.P. De Marco: Materials Science and Engineering A (2007) Vol. 462, p.393.

Google Scholar

[8] A. Rudajevov´a, M. Stanek, P. Luk´aˇc, Mater. Sci. Eng. A 3(2003) Vol. 41, p.152.

Google Scholar

[9] S. Mironov, Q. Yang, H. Takahashi, I. Takahashi, K. Okamoto, Y.S. Sato, and H. Kokawa: The Minerals, Metals & Materials Society and ASM International (2010) Vol. 41A, p.1016.

Google Scholar

[10] R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, and A.K. Mukherjee: Scripta Mater. (2000), vol. 42, p.163.

Google Scholar

[11] Z.Y. MA, Metall. Mater. Trans. A 39 (2008) 642–658.

Google Scholar