High Temperature Performance of TiAlON Thin Films

K. Tuchida; K. Wathanyu; Chiraporn Auechalitanukul; S. Surinphong

doi:10.4028/www.scientific.net/AMR.622-623.690

Paper Titles

Simulation and Analysis of Three Finger Micro/Nano Gripper Using Different Materials
p.665

Simulation and Analysis of Hot Forging Process of Industrial Hub
p.671

Preparation and Gas Sensing Properties of 2,9,16,23-Tetra-Tert-Butyl-29H, 31H- Copper (II) Phthalocyanine LB Thin Films
p.679

Heredity of the Structure and Properties of Grey Cast Iron Melted on a Basis of Steel Scrap
p.685

High Temperature Performance of TiAlON Thin Films
p.690

Tailoring the Hysteresis Loop of the Si/Cu(10nm)/FeMn(10-30nm)/CoFeB(10nm) Bilayer System
p.695

Investigations on the Effect of Tool Speed and Feed Rate on the Friction Stir Processed AZ31B Magnesium Alloys
p.700

Effect of Process Parameters on Microstructure and Mechanical Properties on Severe Plastic Deformation Process of Aa7075-T6 Aluminum Alloy
p.705

Comparison of Bubble Electrospinning and Needle Electrospinning of Ethylcellulose Ultrafine Fibres
p.710

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 622-623High Temperature Performance of TiAlON Thin Films

High Temperature Performance of TiAlON Thin Films

Abstract:

In this paper, the thermal oxidation behavior, adhesion and tribological properties of TiAlON films coated on hastelloyX substrate, typically used for fuel nozzle in gas turbine engine application, have been studied. The uncoated and coated samples were heated to different temperatures, i.e. 950, 1050 and 1150 °C in the controlled atmosphere. The surface appearance, microstructure, chemical composition and adhesion of films were investigated. The thermal oxidations were observed in all testing conditions showing thicker oxide film at higher temperature. However, spalling of oxide scales was found in hastelloyX and TiAlON coated at 1150°C suggesting the maximum working temperature of < 1150 °C. The critical loads corresponding to the full delamination of the thermal oxidation coated specimens were found to be higher than the non-thermal oxidation specimens. The effect of thermal oxidation on damage patterns during scratch tests, i.e. less chipping and cracking for thermal oxidation specimen, were also observed. The tribological properties were also investigated under different load under room temperature and 600 and 1000°C. The results suggested significant improvement in wear resistance of coated sample especially at low load at all temperatures.

You might also be interested in these eBooks

Manufacturing Science and Technology III

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 622-623)

Pages:

690-694

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.622-623.690

Citation:

Cite this paper

Online since:

December 2012

Authors:

K. Tuchida, K. Wathanyu, Chiraporn Auechalitanukul, S. Surinphong

Keywords:

Adhesion, Cathodic Arc PVD, Hastelloy X, Thermal Oxidation, TiAlON, Wear Rate

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] W.Z. Friend : Corrosion of Nickel and Nickel-Base Alloys, John Wiley & Sons, Inc. (1980).

Google Scholar

[2] M. Hetmanczyk, L. Swadzba and B. Mendala : Journal of Achievements in Materials and Manufacturing Engineering Vol. 24 Issue 1(2007), pp.372-381.

Google Scholar

[3] R.A. Mahesh, R. Jayaganthan and S. Prakash : Journal of Materials Processing Technology 09 (2009), pp.3501-3510.

Google Scholar

[4] N. Eliaz, G. Shemesh and R.M. Latanision : Engineering Failure Analysis 9 (2002), pp.31-43.

Google Scholar

[5] W. Satana, K. Tuchinda, A. Tuchinda and S. Chutima, Submitted to The 2012International Conferenceon Mechanics and Control Engineering, ICMCE 2012, Shanghai, China (2012).

Google Scholar

[6] C.L. Chang, J.W. Lee and M.D. Tseng : Thin Solid Films 517 (2009), pp.5231-5236.

Google Scholar

[7] Y.Y. Chang, C.P. Chang, D.Y. Wang, S.M. Yang and W. Wu : Journal of Alloy and Compounds 461 (2008), pp.361-341.

Google Scholar

[8] T.D. Nguyen, S.K. Kim and D.B. Lee : Surface & Coatings Technology 204 (2009), pp.697-704.

Google Scholar

[9] K. Tuchida, K. Wathanyu and S. Surinphong : Advanced Materials Research Vol. 486 (2012), pp.400-405.

DOI: 10.4028/www.scientific.net/amr.486.400

Google Scholar

[10] J. Sjolen, L. Karlsson, S. Braun, R. Murdey, A. Horling and L. Hultman : Surface & Coatings Technology 201 (2007), pp.6392-6403.

DOI: 10.1016/j.surfcoat.2006.12.006

Google Scholar

[11] K. Tonshoff, B. Karpuschewski, A. Mohlfeld, T. Leyendecker, G. Erkens, H.G. FuB and R. Wenke : Surface & Coatings Technology 108-109 (1998), pp.535-542.

DOI: 10.1016/s0257-8972(98)00637-9

Google Scholar

[12] H. Cho, D.M. Lee, J.H. Lee, K.H. Bang and B.W. Lee : Surface & Coatings Technology 202 (2008), pp.5625-5628.

DOI: 10.1016/j.surfcoat.2008.06.094

Google Scholar

[13] P.R. Roberge : Corrosion Engineering Principles and Practice, MC Graw Hill (2008).

Google Scholar