Simulation Research of Angle Action on Fold-Type Board in Air-Heating Collector

Lin Qiu; Run Ping Niu; Min Yan; Jin Yang

doi:10.4028/www.scientific.net/AMR.706-708.1562

Paper Titles

Research on Temperature Effect on the Natural Frequencies of Continuous Beams Based on Stochastic Subspace Identification
p.1545

Research on the Structure Strength and Vibration Mode of Transformer
p.1549

Secondary Cooling Water Distribution Strategy for Beam Blank Continuous Casting
p.1553

Simulation Analysis of Reciprocating Cutter Based on ADAMS
p.1558

Simulation Research of Angle Action on Fold-Type Board in Air-Heating Collector
p.1562

Stiffness Characteristics of a Rotor Shaft with Slant Crack Including Elliptical Front Edge
p.1566

Study in Interface Appearance Design of Postal Equipment Based on Man-Machine Engineering
p.1570

Study on a New Earth-Fault Distance Protection for Four-Circuit Transmission Lines on the same Tower
p.1574

Study on Dynamic Characteristics of Hydraulic Pressure System of MPM Tube Rolling Mill
p.1580

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 706-708Simulation Research of Angle Action on Fold-Type...

Simulation Research of Angle Action on Fold-Type Board in Air-Heating Collector

Abstract:

In this study a fold-type board collector in air-heating is introduced. The factor of fold-type board collector angle action that contributes to the temperature and velocity field were respectively discussed. Numerical simulation of the thermal properties of fold-type collector on different angle with Fluent software. Numeric simulation calculations shown: the fold-type board collector angle action has a greater influence for the thermal properties of collector in air-heating ,the thermal efficiency when is 30°is better than is 45°and is 60°and under this work simulation condition the optimum angle for folded-type panel air collector will be recommend nearby at =30°.

You might also be interested in these eBooks

Mechatronics and Intelligent Materials III

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 706-708)

Pages:

1562-1565

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.706-708.1562

Citation:

Cite this paper

Online since:

June 2013

Authors:

Lin Qiu, Run Ping Niu, Min Yan, Jin Yang

Keywords:

Angle, Collector, Fold-Type Board, Numerical Simulation

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] L. Varsheny, J. S. Saini. Heat transfer and friction factor correlations for rectangular solar air heater duct packed with wire mesh screen matrices. Solar Energy, 1998, 62(4):255-262.

DOI: 10.1016/s0038-092x(98)00017-6

Google Scholar

[2] Ong K S. Thermal performance of solar air heaters: mathematical model and solution procedure, Solar Energy, 1995, 55(2):93-110. Arulanandam et al. A CFD heat transfer analysis of the transpired solar collector under no-wind conditions. Solar Energy, 1999,67:93-100.

DOI: 10.1016/s0038-092x(00)00042-6

Google Scholar

[3] Cao，Hollands， Brundrett， Heat Exchange Effectiveness of Unglazed Transpired－Plate Solar Collector in 2D Flow，Proceedings of ISES Solar World Congress，1993（05）：351－366.

DOI: 10.1016/b978-008043895-5/50177-6

Google Scholar

[4] Van Decker，Hollands，Brunger，Heat Exchange Effectiveness of Unglazed Transpired－Plate Solar Collector in 3D Flow，Proceedings of Euro Sun96，1996：130－135.

Google Scholar

[5] Van Decker，Hollands，An Empirical Heat Transfer Equation for the Transpired Solar Collectors（Including No－Wind Conditions，Proceedings），Solar World Congress，1999：248－256.

DOI: 10.1016/b978-008043895-5/50176-4

Google Scholar