Impact Erosion of Quartz Crystals by Micro-Particles in Abrasive Waterjet Micro-Machining

Abstract:

Abrasive waterjet (AWJ) micro-machining is a precision processing technology with some distinct advantages. To understand the machining process, the erosion mechanism is presented and discussed when micro-particle impacting on a quartz crystal specimen. It is found that three types of impressions are formed which are craters, micro-dents and scratches. Small-scale craters including crashed zones and radial cracks are associated with plastic flow and subsurface micro-cracks that decrease the material strength, but cause little material removal, while large-scale craters including conchoidal fractures caused by the propagation of lateral cracks dominate the volume change of the specimen. Micro-dents are produced by the impact of particles possessing small kinetic energies, and scratches are generated by particle sliding or rolling over the target surface and make a negligible contribution to material removal. The crater volume generated by the impact of individual particle is then discussed with respect to particle impacting velocity and impact angle. It shows that an increase in particle impact angle or particle velocity increases the crater volume due to the increased conchoidal fractures during the impact process.

• Periodical: Advanced Materials Research (Volume 797)
• Pages: 46-51
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.797.46
• Online since: September 2013
• Authors: H. Qi, J.M. Fan, Jun Wang
• Keywords: Abrasive Jet, Conchoidal Fracture, Erosion, Micro-Particle, Quartz Crystal

References

[1] B.R. Lawn and M.V. Swain: Journal of Materials Science, Vol. 10(1975), pp.113-122.

[2] I.M. Hutchings: Powder Technology, Vol. 76(1993), pp.3-13.

[3] J.Y. Zeng and T.J. Kim: Wear, Vol. 193(1996), pp.207-217.

[4] P.J. Slikkerveer, P.C.P. Bouten and F.C.M.D. Haas: Sensors and Actuators, Vol. 85(2000), pp.296-303.

[5] Q.L. Li, J. Wang and C.Z. Huang: Journal of Applied Physics, Vol. 104(2008), 034903.

[6] J. Wang, T. Nguyen and K.L. Pang: Journal of Applied Physics, Vol. 105(2009), 044906.

[7] K.L. Pang, T. Nguyen, J.M. Fan and J. Wang: Machining Science and Technolology-An International Journal, Vol. 16(2012), pp.547-563.

[8] K.L. Pang, T. Nguyen, J.M. Fan and J. Wang: International Journal of Machine Tools and Manufacture, Vol. 53(2012), pp.118-126.

[9] H. Qi, J.M. Fan and J. Wang: Advanced Materials Research, Vol. 565(2012), pp.339-344.

[10] M. Achtsnick, High Performance Micro Abrasive Blasting. PhD Thesis, Delft University of Technology, The Netherlands, (2005).

[11] A.K. Basak, J.M. Fan, J. Wang and P. Mathew: Wear, Vol. 269(2010), p.269–277.

[12] H.Z. Li, J. Wang and J.M. Fan: International Journal of Machine Tools and Manufacture, Vol. 49(2009), pp.850-858.

[13] I.M. Hutchings: Tribology: Friction and Wear of Engineering Materials, Edward Arnold, London, (1992).

[14] A.J. Sparks and I.M. Hutchings: Wear, Vol. 149(1991), pp.99-110.

[15] S.V. Margolis and D.H. Krinsley: American Journal of Science, Vol. 274(1974), pp.449-464.