Application of a Novel Entrainment Defect Model to a High Pressure Die Casting

Abstract:

Aluminium High Pressure Die Castings are economical to produce in high volumes. However, as greater structural demands are placed on such castings, a more detailed understanding is required of the defects which limit their strength. The process is prone to high levels of surface turbulence and fluid break-up, resulting in the entrainment of air into the liquid metal, which may manifest as trapped air porosity or bifilm defects in the finished part. A novel algorithm was developed and integrated into a commercial computational fluid dynamics (CFD) package, to model mould filling, and the formation and transport of such entrainment defects. A commercial High Pressure Die Casting was simulated using this algorithm, to illustrate its application. Castings were also produced, and the results of tensile testing were summarised in the form of Weibull statistics. It was found that where the algorithm predicted a greater quantity of entrained surface film, a reduction in UTS of about 10% was also observed.

• Periodical: Advanced Materials Research (Volume 922)
• Pages: 801-806
• DOI: https://doi.org/10.4028/www.scientific.net/AMR.922.801
• Online since: May 2014
• Authors: Robert Watson*, Tayeb Zeguer, Simon Ruffle, William D. Griffiths
• Keywords: Aluminium Casting, Computational Fluid Dynamics (CFD), Entrainment

References

[1] N. R. Green and J. Campbell, Statistical distributions of fracture strengths of cast Al-7Si-Mg alloy, Mater. Sci. Eng. A 173 (1993) 261-266.

DOI: 10.1016/0921-5093(93)90226-5

[2] J. Campbell, Complete Castings Handbook, Butterworth-Heinemann, Oxford (2011).

[3] C. Dørum, H. I. Laukli and O. S. Hopperstad, Through-process numerical simulations of the Structural Behaviour of Al-Si Die-Castings, Comp. Mat. Sci. 46 (2009) 100-111.

DOI: 10.1016/j.commatsci.2008.12.022

[4] C Reilly, N.R. Green and M.R. Jolly, The Present State of Modeling Entrainment Defects in the Shape Casting Process, Appl. Math. Model. 37 (2013) 611–628.

DOI: 10.1016/j.apm.2012.04.032

[5] X. Dai, M. Jolly, X. Yang and J. Campbell, Modelling of liquid metal flow and oxide film defects in filling of aluminum alloy castings, IOP Conf. Series: Mater. Sci. Eng. 33 (2012), 012073.

DOI: 10.1088/1757-899x/33/1/012073

[6] C. Reilly, Development Of Quantitative Casting Quality Assessment Criteria Using Process Modelling, PhD Thesis, The University of Birmingham (2010).

[7] Y. Yue and N.R. Green, Modelling of different entrainment mechanisms and their influences on the mechanical reliability of Al-Si castings, IOP Conf. Series: Mater. Sci. Eng. 33 (2012), 012072.

DOI: 10.1088/1757-899x/33/1/012072

[8] M. Tiryakioğlu, D. Hudak, Unbiased estimates of the Weibull parameters by the linear regression method, J. Mater. Sci. 43 (2008) 1914-(1919).

DOI: 10.1007/s10853-008-2457-9

[9] M. Tiryakioğlu and J. Campbell, Weibull Analysis of Mechanical Data for Castings: A Guide to the Interpretation of Probability Plots, Metall. Mater. Trans. A, 41 (2010) 3121-3129.

DOI: 10.1007/s11661-010-0364-6

[10] R. C. H. Cheng and T. C. Iles, Confidence Bands for Cumulative Distribution Functions of Continuous Random Variables, Technometrics. 25 (1983) 77-86.

DOI: 10.1080/00401706.1983.10487822