Methods of Increasing Loadability for the Plastic Cycloidal Gears

Krzysztof Biernacki

doi:10.4028/www.scientific.net/KEM.490.156

Paper Titles

Influence of Magnetorheological Fluid Volume onto Obtained Critical Pressures on Rotary Shaft Seals
p.119

Influence of Shaft Misalignment on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
p.128

The Influence of the K_Hß Factor Determination Method on the Evaluation of the Gear Tooth Surface Durability and Bending Strength
p.135

Investigation of Dynamic Magnetic Fluid Seal Wear Process in Utility Water Environment
p.143

Methods of Increasing Loadability for the Plastic Cycloidal Gears
p.156

Modelling the Contact between the Rolling Elements and the Raceways of Bulky Slewing Bearings
p.166

Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
p.179

Multicaterpillar Track Chassis of Big Machines - Identification of Loads
p.187

New Satellite Pumps
p.195

HomeKey Engineering MaterialsKey Engineering Materials Vol. 490Methods of Increasing Loadability for the Plastic...

Methods of Increasing Loadability for the Plastic Cycloidal Gears

Abstract:

The working unit of the hydraulic gerotor machine consists in cycloidal gears. In the paper, ways of increasing the load limit for the plastic cycloidal gears have been presented . The objective has been achieved by means of structural and material methods. The modifications have been introduced on the basis of the theoretical analysis of stress and deformation that are generated in the cycloidals gears while in operation. The analysis has been carried out with the use of the finite elements method. The outcome of the analysis is determination of the maximum working pressure value at which the hydraulic gerotor machines featuring the plastic cycloidal gears can operate.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 490)

Pages:

156-165

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.490.156

Citation:

Cite this paper

Online since:

September 2011

Authors:

Krzysztof Biernacki

Keywords:

Cycloidal Gears, Deformation, Finite Element Method (FEM), Plastic, Stress

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] S. Bednarczyk, J. Stryczek, and Z. Zienowicz. Gerotor pumps with plastic gears. Hydraulika i Pneumatyka, 2006, (5), pages 16-19. (available at www.simphip.not.pl).

Google Scholar

[2] K. Biernacki, J. Stryczek. Analysis of stress and deformation in plastic gears used in gerotor pumps. The Journal of Strain Analysis for Engineering Design, October 2010, vo.45, Issue 7, pages 465-479.

DOI: 10.1243/03093247jsa630

Google Scholar

[3] K. Biernacki, J. Stryczek. Design of plastic cycloidal gears used in the gerotor pump. HYDRAULIKA I PNEUMATYKA NR 6/2010, str. 30 - 33.

Google Scholar

[4] D. Capanidis. Tribological testing of polioxymethylene (POM) – Tarnoform sliding composites. TRIBOLOGIA Nr 3/2004 (str. 25-33).

Google Scholar

[5] E. Rusiński, J. Czmochowski, T. Smolnicki. Advanced finite element method in the load-bearing structures Publishing House of Wrocław University of Technology. Wrocław 2000.

Google Scholar

[6] J. Stryczek. Cycloidal gears in design of gear pumps and motors. Habilitation Dissertation. Scientific Papers of the Institute of Machine Design and Operation of Wroclaw University of Technology. Series: Monographs nr 15. Wroclaw 1991.

Google Scholar

[7] J. Stryczek, Gears of the hydraulic machines. Publishing House of Wrocław University of Technology.Wrocław2007. http://www.dbc.wroc.pl/dlibra/docmetadata?id=20045&from=&dirids=1

Google Scholar