Factors Affecting the Fracture Strength of Freestanding Diamond Films

Abstract:

As an emerging brand new type of engineering material for a variety of important high technology applications, the deep understanding of the mechanical behavior of freestanding diamond films has become an emergent task of vital importance. Unfortunately the mechanical behavior of this brand new material is not fully understood. Effects that affect the fracture strength are still not very clear except that the fracture strength of freestanding diamond films is only depended on the grain size (film thickness), and is insensitive to the microscopic defects, and the strength is considerably higher when the nucleation side is in tension than that when the growth side is in tension. However, this is not the full story. Based on the experimental date accumulated in USTB (University of Science and Technology Beijing) for high power dc arcjet diamond films, other factors that may affect the fracture strength of freestanding diamond films are discussed in detail. Effects of the quality of the diamond films, impurities (nitrogen, hydrogen, non-diamond carbon etc.), film morphology and texture, on fracture strength are discussed. Effects of the deposition parameters are explained. Advantages for small amount of nitrogen addition, and for the use of higher substrate temperatures in the increase in fracture strength are demonstrated, which have already been applied in the mass production of tool grade freestanding diamond films. It is hoped that the present paper will be helpful for those who wish to understand and use this brand new type of engineering material

• Periodical: Key Engineering Materials (Volume 537)
• Pages: 1-6
• DOI: https://doi.org/10.4028/www.scientific.net/KEM.537.1
• Online since: January 2013
• Authors: J.H. Song, F.X. Lu, L.F. Hei, C.M. Li, W.Z. Tang, G.C. Chen
• Keywords: Fracture Strength, Freestanding Diamond Film, High Power Dc Arcjet, Influencing Factor

References

[1] N.V. Novikov, Synthesis of superhard materials, Journal of Materials Processing Technology.  161(1-2) (2005) 169-172

[2] A. Gicquel, K. Hassouni, F. Silva, J. Achard, CVD diamond films: from growth to applications, Current Applied Physics.  1(6) (2001) 479-496

DOI: 10.1016/s1567-1739(01)00061-x

[3] Katsuyuki Okada, Plasma-enhanced chemical vapor deposition of nanocrystalline diamond, Science and Technology of Advanced Materials.  8(7-8) (2007) 624-634

DOI: 10.1016/j.stam.2007.08.008

[4] X. W. Zhu, D. M. Aslam, CVD diamond thin film technology for MEMS packaging, Diamond & Related Materials, 15 (2006) 254–258

DOI: 10.1016/j.diamond.2005.08.009

[5] F.X.Lu, G.F. Zhong, J.G. Sun et al. A New Type of DC Arc Plasma Torch for Low Cost Large Area Diamond Deposition. Diamond and related Materials, 7/6 (1998) 737-741

DOI: 10.1016/s0925-9635(97)00180-5

[6] F.X. Lu, W. Z. Tang, G.F. Zhong et al. Economical Deposition of Large Area High Quality Diamond Film by High Power DC Arc Plasma Jet Operating in Gas Recycling Mode, Diamond and Related Materials, 9 (9–10), (2000) 1655

DOI: 10.1016/s0925-9635(00)00305-8

[7] F.X. Lu, Large Area Optical Grade Freestanding Diamond Films: Deposition, Characterization, and High Technology Application Prosperous. Chinese Surface Engineering, 23 (3), (2010) 1-13

[8] J.E. Field, C.S.J. Pickles, Strength, fracture and friction properties of diamond. Diamond and Related. Materials. 5 (1996) 625-634

DOI: 10.1016/0925-9635(95)00362-2

[9] L.F. Hei, F.X. Lu, C.M. Li et al., A Review on Mechanical Properties of Freestanding Diamond Films, Advanced materials Rsearch, 490-495 (2012) 3059-3064

DOI: 10.4028/www.scientific.net/amr.490-495.3059

[10] F.X. Lu, Z. Jiang, W.Z. Tang, T.B. Huang and J.M. Liu, Accurate measurement of strength and fracture toughness for miniature size thick diamond film samples by three point bending at constant loading rate. Diamond and Related Materials, 10 (2001) 770-774

DOI: 10.1016/s0925-9635(00)00523-9

[11] S.B. Guo, Y.H. Wang, F. Chen, F.X. Lu, W.Z. Tang, Y.M. Tong, Effect of the quality of diamond film deposited by dc arc plasma jet CVD on physical properties, Gongneng Cailiao, 38 (2007) 3802 – 3805

[12] S.B. Guo, Study of the effect of minute impurities on physical properties of diamond films, Ph.D. Thesis, University of Science and Technology Beijing, (2009)

[13] H. Chatei, J. Bougdira, M. R emy, et al. Effect of nitrogen concentration on plasma reactivity and diamond growth in a H2-CH4-N2 microwave discharge, Diamond and Related Materials, 6(1) (1997) 107-119

DOI: 10.1016/s0925-9635(96)00588-2

[14] J. Asmussen, J. Mossbrucher, S. Khatami, et al. The effect of nitrogen on the growth, morphology, and crystalline quality of MPACVD diamond films, Diamond and Related Materials, 8(2-5) (1999) 220-225

DOI: 10.1016/s0925-9635(98)00371-9

[15] Y. Avigal, O. Glozman, I. Etsion, et al. [100]-textured diamond films for tribological applications, Diamond and Related Materials, 6(2-4) (1997) 381-385

DOI: 10.1016/s0925-9635(96)00625-5

[16] C.J. Tang, A.J. Neves, Jose´ Gra´cio, A.J.S. Fernandes, M.C. Carmo, A new chemical path for fabrication of nanocrystalline diamond films, Journal of Crystal Growth 310 (2008) 261–265

DOI: 10.1016/j.jcrysgro.2007.10.051

[17] V. Ralchenko, S. Pimenov, V. Konov et al., Nitrogenated nanocrystalline diamond films: Thermal and optical properties, Diamond & Related Materials 16 (2007) 2067–(2073)

DOI: 10.1016/j.diamond.2007.05.005

[18] O.A. Williams, Nanocrystalline diamond, Diamond and Related Materials, 20 (2011) 621-640

DOI: 10.1016/j.diamond.2011.02.015

[19] F.X. Lu, H.D. Zhang, W.Z. Tang et al., Dielectric property of thick freestanding diamond films by high power arcjet operating at gas recycling mode, Diamond and Related Materials, 13(9), (2004) 1714-1718

DOI: 10.1016/j.diamond.2004.02.011

[20] J.X. Yang, H.D. Zhang, F.X. Lu et al., Effects of nitrogen addition on morphology and mechanical property of DC arc plasma jet CVD diamond films, Diamond and Related Materials, 13 (2004) 139–144

DOI: 10.1016/j.diamond.2003.10.028

[21] J.X. Yang, C.M. Li, F.X. Lu, G.C. Chen, W.Z. Tang, Y.M. Tong, Microstructure and fracture strength of different grades of freestanding diamond films deposited by a DC Arc Plasma Jet process, Surface & Coatings Technology 192 (2005) 171– 176

DOI: 10.1016/j.surfcoat.2004.04.089

[22] H.D. Zhang, J.Z. Tian, W.Z. Tang, F.X Lu, Correlation Between the Fracture Strength and the Crystal Orientation of thick Freestanding Diamond Films, Carbon, 41(3) (2003) 603-606

DOI: 10.1016/s0008-6223(02)00408-6