Research and Design of an Equipment for Multi-Point Press Forming Sheet Metal Parts

Ru Yu Ma; Hua Ding; De Yong Yang

doi:10.4028/www.scientific.net/KEM.575-576.467

Paper Titles

Annealing and Deposition Parameters Influence on the Performance of AlN Thin Films
p.441

Advances in Development of Titanium Alloys for Spinal Fixation Applications-Titanium Alloys with High Fatigue Strength and Low Springback for Spinal Fixation Applications-
p.446

Development of Changeable Young's Modulus with Good Mechanical Properties in β-Type Ti-Cr-O Alloys
p.453

Foamed Glass-Ceramics Made from Red-Mud
p.461

Research and Design of an Equipment for Multi-Point Press Forming Sheet Metal Parts
p.467

Influence of Negative Voltage on Micro-Arc Oxidation of Magnesium Alloy under Two Steps Voltage-Increasing Mode
p.472

Formaldehyde Gas Sensor Based on Pentacene Organic Thin-Film Transistor
p.477

Design and Test of Controlled Droplet Sprayer for Facility Agriculture
p.481

Discussion on Applicability of the Technology of Using Light to Trap in the Field of Pests and Diseases Control in Tea Plantation of China
p.487

HomeKey Engineering MaterialsKey Engineering Materials Vols. 575-576Research and Design of an Equipment for...

Research and Design of an Equipment for Multi-Point Press Forming Sheet Metal Parts

Abstract:

The premise of the flexible multi-point die stamping processing is that each punch can be adjusted to required position. Using numerical control technique, punches can be adjusted by stepping motors through driving screw rods. But each punch requires a stepping motor in this equipment. This kind of equipment is much expensive. In addition, the distance between adjacent punches is much big. Thus, this kind of equipments is not suitable for processing some small and medium-sized sheet metal parts. A new kind of equipment for press forming sheet metal parts is presented. Only two DC motors are needed to adjust punches of male and female moulds in this kind of equipment. Punches can be arranged more closely. This kind of equipments can be used to process small and medium-sized sheet metal parts.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 575-576)

Pages:

467-471

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.575-576.467

Citation:

Cite this paper

Online since:

September 2013

Authors:

Ru Yu Ma, Hua Ding, De Yong Yang

Keywords:

Die, Equipment, Multi-Point, Punch, Sheet Metal Part

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] C.Q. Ji, Numerical Simulation and Forming Performance Comparison on the Process of Mult-Point Forming and Die Forming for Sheet Mental, Master's degree thesis of Jilin University. (2006).

Google Scholar

[2] Z.M. Li, Z.Y. Cai, X.J. Cui, Multi-point Forming-A New Flexible Forming Process for Sheet Metal, Metal forming technology. 20 (2002) 5-9.

Google Scholar

[3] L.W. Zhang, Q. Zhong B. Lv, et al., Research and Application of Laser Sheet Bending, New Technology & New Process. 3 (2005) 47-50.

Google Scholar

[4] X.Q. Zhang, J.Z. Zhou, G.L. Wang, et al., Technology of laser peening and its application, Manufacturing Automation. 27 (2005) 26-28.

Google Scholar

[5] S.J. Yuan, B.G. Teng, The dieless hydro-bulging technology, Journal of Plasticity engineering, 11 (2004) 9-20.

Google Scholar

[6] A.P. Song, H. Yi, W. C. Tang, Poles flexible die and its key technology of sheet forming process, China Mechanical Engineering, 16 (2005) 1966-(1969).

Google Scholar