Paper Titles

Dynamic Frictions between AISI 316L and 3M^TM Trizact^TM Structured Abrasive Belts during Mirror-Like Polishing
p.227

The Effect of CNT Content on the Tribological Properties of CNTs Doped Diamond-Like Carbon Films
p.231

The Study of Band Sawing Vibration and Cutting Performance
p.236

Surface Roughness and Magnetic Effect of Magnetized Journal Bearings Lubricated with Ferrofluid
p.242

Elastic-Plastic Analysis of Fretting Contacts
p.248

The Effect of Surface Modification of Polytetrafluoroethylene (PTFE) on the Properties of POM/PTFE Fiber Composites
p.253

Observation of the Tribo-Film Formation Derived from ZnDTP by Using FT-IR
p.259

Tribological Study of PCL-PEG-PCL Polymer on SiN_xH_y Base
p.264

Optical Measurement of EHL Film under Oscillating Needle Roller Contacts
p.270

HomeKey Engineering MaterialsKey Engineering Materials Vol. 642Elastic-Plastic Analysis of Fretting Contacts

Elastic-Plastic Analysis of Fretting Contacts

Article Preview

Abstract:

A finite element procedure is implemented for the elastic-plastic analysis of carbon steels subjected to reciprocating fretting contacts. The nonlinear kinematic hardening rule based on Chaboche model is used to model the cyclic plastic behavior in fretting contacts. The results show that accumulation of plastic strains, i.e. ratchetting, may occur near the contact edge while elastic shakedown is likely to take place in substrate.

You might also be interested in these eBooks

Tribology Engineering

Info:

Periodical:

Key Engineering Materials (Volume 642)

Pages:

248-252

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.642.248

Citation:

Cite this paper

Online since:

April 2015

Authors:

Chang Hung Kuo*

Keywords:

Cyclic Plasticity, Elastic-Plastic Finite Element Analysis, Fretting, Nonlinear Kinematic Hardening Rule, Ratchetting

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2015 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

[1] R. D. Blevins: Trans ASME, J Eng Power Vol. 101 (1969), p.625.

[2] R.B. Waterhouse: Fretting Wear, ASM Handbook Vol. 18 (1992), p.233.

[3] H.J. Connors: Nucl Technol Vol . 55 (1982) p.311.

[4] E.M. Eden, W.N. Rose and F.L. Cunningham: Proc. Inst. Mech. Engrs Vol. 4 (1911), p.839.

[5] G.A. Tomlinson: Proc. Roy. Soc. Lond. A Vol. 115 (1927), p.472.

[6] S.R. Brown: ASTM STP 780 (1982).

[7] O. Vingsbo, S. Soderber: Wear Vol. 126 (1988), p.131.

[8] Z.R. Zhou and L. Vincent: Wear Vol. 181-183 (1995), p.531.

[9] J. Ding, G. Bandak, S.B. Leen, E.J. Williams and P.H. Shipway: Tribol. Int. Vol 42 (2009), p.1651.

[10] H.M. Zhu and Z.R. Zhou: Tribol. Int. Vol. 44 (2011), p.1378.

[11] C. Petiot, L. Vincent, K. Dang Van, N. Maouche, Foulquier, J. and B. Jounet: Wear Vol. 181 (1995), p.101.

[12] S. Fouvry, P. Kapsa and L. Vincent: Wear Vol. 200 (1996), p.186.

[13] C.T. Tsai and S. Mall: Finite Elem. Anal. Des. Vol. 36 (2000), p.171.

[14] J.M. Ambrico and M.R. Begley: J. Mech. Phys Solids Vol. 48 (2000) p.2391.

[15] A.L. Mohd Tobi, J. Ding, G. Bandak, S.B. Leen and P.H. Shopway: Wear Vol. 267 (2009), p.270.

[16] D.A. Hills, D. Nowell and A. Sackfield: Mechanics of Elastic Contacts, Butterworth-Heinemann (1993).

[17] J.L. Chaboche: Int. J. Plasticity Vol. 2 (1986), p.149.

[18] S. Bari and T. Hassan: Int. J. Plasticity Vil. 16 (2000), p.381.