Application of Sand Casting to Recycle Aluminum Alloy for Motorcycle Brake Handle

I Nyoman Gde Antara; Karohika Gatot Made; Gunawan Ketut

doi:10.4028/www.scientific.net/KEM.705.357

Paper Titles

Modeling the Heat of Hydration of Concrete Incorporating Fly Ash
p.332

Optimization of Radiation Shielding Concrete for Radiotherapy Treatment Room at Bangabandhu Sheikh Mujib Medical University
p.338

Compressive Strength and Water Penetration of Concrete with Enterococcus faecalis and Calcium Lactate
p.345

Experimental Research on Creep Laws of High-Water Material under Real Pressure Water Environment
p.350

Application of Sand Casting to Recycle Aluminum Alloy for Motorcycle Brake Handle
p.357

How to Increase Plastic Waste Acceptance for Mechanical Recycling: An Introduction to Material Value Conservation and its Phenomenon
p.362

Processing Zinc from Waste of Used Zinc-Carbon Battery with Natrium Chloride (NaCl) for Biogas Desulfurizer
p.368

Precious Nickel Recovery from Palm Oil Mill Fuel Ash Waste (Ni-POMFAW) Using Acidic Leaching Extraction (ALE)
p.374

Remediation of Raw Wastewater of Palm Oil Mill Using Activated Cow Bone Powder through Batch Adsorption
p.380

HomeKey Engineering MaterialsKey Engineering Materials Vol. 705Application of Sand Casting to Recycle Aluminum...

Application of Sand Casting to Recycle Aluminum Alloy for Motorcycle Brake Handle

Abstract:

The development of the automotive industry brings impact of increasing use of aluminum for vehicle components that will ultimately produce more aluminum waste. If it is not addressed properly, it will be a serious problem for the environment. One of the solutions is to recycle the waste of drum brake to be a raw material for motorcycle accessories brake handle. The process of making motorcycle brake handle using the sand casting method can be done by varying the temperatures of casting molten metal which are at temperatures of 650°C, 700°C and 750°C. Furthermore, the testing of the mechanical properties and microstructure of the resulted product is done. The result shows that motorcycle brake handle required high impact strength in which the highest impact strength was 0.011 Nm/mm2 that was obtained when temperature of casting was 700°C.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 705)

Pages:

357-361

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.705.357

Citation:

Cite this paper

Online since:

August 2016

Authors:

I Nyoman Gde Antara, Karohika Gatot Made, Gunawan Ketut*

Keywords:

Casting Temperature, Hardness, Impact, Microstructure, Sand Casting, Tensile Strength

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Jirang Cui and Hans J. Rovens: Transaction of Nonferrous Metals Society of China vol. 20, November 2010, pages 2057-(2063).

Google Scholar

[2] V. Guley, N. Ben Khalifa, A. E. Tekkaya: Int J Mater Forum (2010) vol. 3 pages: 853-856.

Google Scholar

[3] Ning Ding, Feng Gao, Zhihong Wang, Xianzheng Gong, Zuoren Nie: Procedia Engineering vol. 27, 2012, pages 465-474.

Google Scholar

[4] Zeljko Kamberovic, Endre Romhanji, Mirjana Filipovic, Marija Korac: Association of metallurgical engineers of Serbia, MJoM Vol 15 (3) 2009 pp.189-200.

Google Scholar

[5] Francis Uchenna Ozioko: Leonardo Electronic Journal of Practices and Technologies, ISSN 1583-1078, 2012, pp.82-92.

Google Scholar

[6] Grill P. L., Principle of Metal Casting, McGraw-Hill Book Company, New York, 1982, pp.160-166.

Google Scholar

[7] Mohammad B. Ndaliman and Akpan P. Pius: Leonardo Electronic Journal of Practices and Technologies, ISSN 1583-1078, 2007, pp.71-80.

Google Scholar

[8] Mahipal Singh, Manjinder Bajwa, Rohit Sharma, Hitesh Arora: International Journal of Scientific & Engineering Research, Volume 4, Issue 6, June-(2013).

Google Scholar