The Selection of Appropriate Process Parameters of Diffusion Bonding in Heterogeneous Weld of 355J2/AISI 316L Steels

Jaromír Moravec; Iva Nováková

doi:10.4028/www.scientific.net/KEM.737.101

Paper Titles

Investigation on Hole Punching Process with Combined Punch to Improve Surface Quality during the Materials Forming Process
p.77

Modelling Kerf Width in WEDM Titanium Alloy Using Response Surface Methodology
p.83

Effect on Hardness and Microstructures of Rail Joint with Ultra-Narrow Gap Arc Welding by Post Weld Heat Treatment
p.90

Evaluation of Surface Quality and Signal Characteristics in Milling Process of Al7075-T651
p.95

The Selection of Appropriate Process Parameters of Diffusion Bonding in Heterogeneous Weld of 355J2/AISI 316L Steels
p.101

Effect of in Addition on Microstructure and Properties of Zn-5Al Solder
p.107

Analysis of Possible Application of Temperature Dependences of Processed Materials’ Physical and Mechanical Properties to Define the Maximum Workability Temperature
p.114

Investigation on Wear Behavior of Bamboo Filler Reinforcement of Injection Moulded Plastic Gear
p.119

Research on Formability of Multi-Point Press Forming for 08Al and 2024-O Sheet
p.124

HomeKey Engineering MaterialsKey Engineering Materials Vol. 737The Selection of Appropriate Process Parameters of...

The Selection of Appropriate Process Parameters of Diffusion Bonding in Heterogeneous Weld of 355J2/AISI 316L Steels

Abstract:

The aim of this article is to present possibilities of diffusion bonding utilization at creation heterogeneous joints where strength properties are taken into account. The joint was implemented to low-alloy structural ferrite-pearlite S355J2 steel and high-alloy austenitic AISI 316L steel. The fundamental theory of diffusion and also design and realisation of experimental creation of diffusion joint in thermal-mechanical simulator Gleeble 3500 is described in the article. Furthermore, procedure of technological parameters selection, when optimisation of strength properties of heterogeneous joint including metallographic evaluation are taken into account, are presented.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 737)

Pages:

101-106

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.737.101

Citation:

Cite this paper

Online since:

June 2017

Authors:

Jaromír Moravec*, Iva Nováková

Keywords:

316l Steel, Diffusion Welding, Gleeble 3500, Process Parameters, S355J2 Steel

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] J. Pluhar, A. Puskar, J. Koutsky, J. Macek, V. Benes, Fyzikální metalurgie a mezní stavy materiálu, SNTL/ALFA, Praha, (1987).

Google Scholar

[2] L. Onsager, Reciprocal Relations in Irreversible Processes, I., Phys. Rev. 37 (1931) 405-426.

DOI: 10.1103/physrev.37.405

Google Scholar

[3] O. Volenik, Difuze v kovech, ČS časopis pro fyziku, (1964).

Google Scholar

[4] Information on http: /fs1. vsb. cz/~hla80/2009Svarovani/01Historie. pdf.

Google Scholar

[5] Information on http: /iss-cheb. cz/projekt/Sva%C5%99ov%C3%A1n%C3%AD. pdf.

Google Scholar

[6] J. Moravec, M. Dikovits, I. Novakova, O. Caliskanoglu. A comparison of dilatometry results obtained by two different devices when generating CCT and in-situ diagrams, Key Eng. Mater. Switzerland: Trans Tech Publications, 669 (2015).

DOI: 10.4028/www.scientific.net/kem.669.477

Google Scholar

[7] I. Jauhari, H. Ogiyama, H. Tsukuda. Solid state diffusion bonding of superplastic duplex stainless steel with carbon steel. J. Soc. Mater. Sci. 9(2) (2003) 154-159.

DOI: 10.2472/jsms.52.6appendix_154

Google Scholar

[8] M. F. Araújo, O. R. Bagnato, Corrosive and metallographic test analysis in stainless steel AISI 316L joined by Diffusion Bonding, LNLS, Campinas, (2008).

Google Scholar

[9] S. Kumar, J. Krishnamoorthi, B. Ravisankar, B. Angelo, Methodology to evaluate the quality of diffusion bonded joints by ultrasonic method. IJEMS. 16(5) (2009) 331-334.

Google Scholar

[10] D. Dopjera, R. Konar, M. Mician, Ultrasonic testing of girth welded joint with TOFD and Phased Array, In: Manufacturing technology: J. Sci. Res. Prod. ISSN 1213-2489. 14(3) (2014) 281-286.

DOI: 10.21062/ujep/x.2014/a/1213-2489/mt/14/3/281

Google Scholar

[11] R. Konar, M. Mician, Non-destructive testing of welds in gas pipelines repairs with Phased Array ultrasonic technique, In: Manufacturing technology: J. Sci. Res. Prod. - ISSN 1213-2489. 14(1) (2014) 42-47.

DOI: 10.21062/ujep/x.2014/a/1213-2489/mt/14/1/42

Google Scholar