Efficiency of Application of Epilams when Protecting the Surface of Fast Cutting Tools

Abstract:

The article discusses the issues of increasing the efficiency of using nanocoatings of the working surfaces of a tool operating at relatively low cutting speeds. A theoretical and experimental approach is proposed, which is based on a model of the interaction of the internal three-dimensional state of the epilame layer, a two-dimensional material film and the material line closing it. An analysis of the state and shape of a liquid layer on a flat surface is given under the assumption that Young's equation is valid, which connects the contact angle with the values of surface stresses. Dependencies and a technique are given that allow you to control the behavior of an epilame drop on the surface of the cutting element. It was found that when thin-film coatings are applied from epilame solutions, a film is created on the surface of the instrument, which significantly changes the energy properties of the surface. It is shown that during the study of oil absorption of epilamated and unepilamated surfaces, as well as the study of the behavior of oil, the greatest retention of oil is observed during intermittent epilamated, presented in the form of large drops, the area of which depends on the area of unepilamated areas. It is recommended to carry out the following experimental research technique, which is associated with obtaining the initial parameters for determining the geometric parameters of a drop of the material under study on a flat surface. The radius of the projection of the drop onto the substrate, the profile of the drop when scanning the side view and then taking into account that the drop is a figure of rotation are determined, taking into account the previous data, its volume, the value of the wetting angle and the height of the drop are determined.

• Periodical: Key Engineering Materials (Volume 910)
• Pages: 163-171
• DOI: https://doi.org/10.4028/p-ezu6o1
• Online since: February 2022
• Authors: Larisa Yu. Frolenkova, Alexander S. Tarapanov, Michael F. Selemenev*, Alexander D. Novikov, Elena M. Selemeneva
• Keywords: Edge Wetting Angle, Epilams, Work Surface

References

[1] Selemenev M.F., Kirichek A.V., Selemeneva O.V. The influence of epilams (surfactants) on the physical and technical properties of tools at low-speed machining / Fundamental and applied problems of engineering and technology, 2017, No. 2 (322).

[2] Selemenev M.F., Selemeneva O.V., Frolenkova L.Yu., Tarapanov A.S. Theoretical analysis of the resistance of epilamated coatings of the tool under surface plastic deformation / Journal Fundamental and Applied Problems of Engineering and Technology,. - Oryol: OSU named after I.S. Turgenev, No. 1 (327), 2018. - S. 37-42. [No. 2152 from the list of J. VAK RF, as of 27.05.2018].

[3] Novikov A.D., Selemenev M.F., Frolenkova L.Yu., Tarapanov A.S. Analysis of the shaping of internal profiles using computer modeling // Materials of the International Scientific Symposium of Mechanical Engineers (Rostov-on-Don, 26-28 September 2018). - 2018.- P. 123 - 126.

[4] Selemenev M.F., Novikov A.D., Selemenev K.F. The role of nanocoatings in increasing the resistance of taps / Izvestiya OSU named after Turgenev. Fundamental and applied problems of engineering and technology "No. 6, (331) Oryol: OSU named after I.S. Turgenev, (2018).

DOI: 10.53040/9789975566957.38

[5] Selemenev M.F., Gubareva L.I., Selemeneva E.M., Cherepenko A.A. Thermal mechanical deformations of complex-profile working surfaces under cyclic loading / Izvestiya OSU named after Turgenev. Fundamental and applied problems of engineering and technology ,No. 6, (332) (2018).

[6] M.F Selemenev, Ivanov V.V., Pogorelov N.P., Sakunov A.A. Research of micro and nano profalile surface morphology of vibrotional mechanical and chemical zinc coating / MATEC Web of Conferences matecconf/201822 0 https://doi.org/10.1051/ 1018.

DOI: 10.1051/matecconf/201822601018

[7] M.F Selemenev, V.A. Lebedev, G. Serga, L. Chunakhova Processing Equipment on the Basis of Operative Parts in the Form of Screw Rotors with Profiled Perimeter / MATEC Web Conf. Volume 297, 2019 X International Scientific and Practical Conference Innovations in Mechanical Engineering, (ISPCIME-2) https://doi.org/10.1051/matecconf/201929702004.

DOI: 10.1051/matecconf/201929702004

[8] M.F. Selemenev, L Yu Frolenkova, A S Tarapanov Increasing the efficiency of vibration treatment of complex surfaces / IOP Conf. Series: Materials Science and Engineering 709 (2020) 044077 IOP Publishing.

DOI: 10.1088/1757-899x/709/4/044077

[9] M.F. Selemenev, A.D. Novikov, L.Y. Frolenkova, A.S. Tarapanov Prediction of the stability of nanocoatings of tool working surfaces / MATPR-D-20-04797.

DOI: 10.1016/j.matpr.2020.08.239

[10] Mihail Selemenev, Larissa Frolenkova, Alexander Tarapanov, Alexander Novikov and Elena Selemeneva Adhesion resistance ofnanocoatings of tool workingsurfaces / MATEC Web Conf. Volume 329, 2020International Conference on Modern Trends in Manufacturing Technologies and Equipment: Mechanical Engineering and Materials Science (ICMTMTE 2020) https://doi.org/10.1051/matecconf/202032902006.

DOI: 10.1051/matecconf/202032902006

[11] Mihail F Selemenev Experimental Studies of Deformation and Temperature Processes Mandrelling in the Deform-3D System / Mihail F Selemenev, Arkady A. Cherepenko, Elena A. Zvyagina, Artem N. Tkachenko and Elena M. Selemeneva // Materials Science Forum Submitted: 2021-01-28 ISSN: 1662-9752, Vol. 1037, pp.357-368 Accepted: 2021-03-16 © 2021 Trans Tech Publications Ltd, Switzerland, 357 - 368.

DOI: 10.4028/www.scientific.net/msf.1037.357