Second Phase Dissolution Evolution of an As-Cast Al-4.0Cu-1.0Li-0.4Mg-0.3Ag-0.1Zr Alloy during Multiple Homogenization Processes

Abstract:

Homogenization treatment is vital for eliminating eutectic structure and ensuring a preferable microstructure foundation for Aluminum Lithium (Al-Li) alloys. In this paper, solidification phases in an as-cast Al-Li alloy were revealed and their evolutions during multiple homogenization processes were analyzed by means of scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and differential scanning calorimetry (DSC) analysis. The results showed that the as-cast microstructure mainly contained needlelike Al₂CuLi and Al₂Cu phase, large size Cu-rich phases and netlike Ag-containing phases attached to them. As the alloy homogenized by 455°C/16h, except for needle-like phases inside grains, part of phases on grain boundaries had dissolved into the matrix and exhibited rounded shapes. As homogenized by 455°C/16h+495°C/16h, Ag-containing phase had completely dissolved into the matrix while the Cu-rich phases remained and showed two different morphologies depending on whether Mg element was contained. Prolonging the second homogenization time to 28h, no obvious change occurred for the Cu-rich phase. As homogenized by 455°C/16h+495°C/20h+512°C/20h, most Cu-rich phase had dissolved into the matrix while residual phase was mainly Fe-containing phase. This proposes an effective way to eliminate various solidification phases in Al-Li alloys and identify their contents.

• Periodical: Key Engineering Materials (Volume 921)
• Pages: 75-83
• DOI: https://doi.org/10.4028/p-6w455x
• Online since: May 2022
• Authors: Ben Lin, Kai Wen*, Yong An Zhang, Zheng Gen Hu, Hui Qiang Wu
• Keywords: Al-Li Alloy, Homogenization, Second Phase Dissolution

References

[1] T. Dursun, C. Soutis. Recent development in aluminium alloys for aerospace applications, Mater. Des. 2014, 56: 862-871.

[2] B. Xie, L. Huang, J. Xu, et al. Effect of the aging process and pre-deformation on the precipitated phase and mechanical properties of 2195 Al–Li alloy, Mater. Sci. Eng. A. 2022, 832: 142394.

DOI: 10.1016/j.msea.2021.142394

[3] A.A. El-Aty, Y. Xu, X. Guo, et al. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: A review, J. Adv. Res. 2018, 10: 49-67.

DOI: 10.1016/j.jare.2017.12.004

[4] L. Wang, C. Kong, H. Yu. Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures, J. Alloy. Compd. 2022, 900: 163442.

DOI: 10.1016/j.jallcom.2021.163442

[5] X. Yang, J. Wang, M. Zhang, et al. Achieving high strength and ductility of Al-Cu-Li alloy via creep aging treatment with different pre-strain levels, Mater. Today Commun. 2021, 29: 102898.

DOI: 10.1016/j.mtcomm.2021.102898

[6] X. Chen, X. Ma, H. Xi, et al. Effects of heat treatment on the microstructure and mechanical properties of extruded 2196 Al-Cu-Li alloy, Mater. Des. 2020, 192: 108746.

DOI: 10.1016/j.matdes.2020.108746

[7] Y. Wang, X. Ma, G. Zhao, et al. Microstructure evolution of spray deposited and as-cast 2195 Al-Li alloys during homogenization, J. Mater. Sci. Technol. 2021, 82: 161-178.

DOI: 10.1016/j.jmst.2020.12.028

[8] S. Duan, F. Guo, S. Qin, et al. Effects of cooling rates on precipitates in homogenized Al–Cu–Li alloy, Mater. Lett. 2021, 293: 129695.

DOI: 10.1016/j.matlet.2021.129695

[9] Q. Liu, G. Fan, Z. Tan, et al. Precipitation of Al3Zr by two-step homogenization and its effect on the recrystallization and mechanical property in 2195 Al–Cu–Li alloys, Mater. Sci. Eng. A. 2021, 821: 141637.

DOI: 10.1016/j.msea.2021.141637

[10] A. Medjahed, A. Henniche, M. Derradji, et al. Effects of Cu/Mg ratio on the microstructure, mechanical and corrosion properties of Al-Li-Cu-Mg-X alloys, Mater. Sci. Eng. A. 2018, 718: 241-249.

DOI: 10.1016/j.msea.2018.01.118

[11] X.Y. Wang, J.T. Jiang, G.A. Li, et al. Effects of coarse Al2CuLi phase on the hot deformation behavior of Al–Li alloy, J. Alloy. Compd. 2020, 815: 152469.

DOI: 10.1016/j.jallcom.2019.152469

[12] J. Tao, L. Zhang, G. Wu, et al. Effect of heat treatment on the microstructure and mechanical properties of extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy, Mate. Sci. Eng. A. 2018, 717: 11-19.

DOI: 10.1016/j.msea.2018.01.063

[13] E. Gumbmann, W. Lefebvre, F.D. Geuser, et al. The effect of minor solute additions on the precipitation path of an AlCuLi alloy, Acta Mater. 2016, 115: 104-114.

DOI: 10.1016/j.actamat.2016.05.050

[14] Y.J. Guo, J.F. Li, D.D. Lu, et al. Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy, Mater. Charact. 2021, 182: 111549.

DOI: 10.1016/j.matchar.2021.111549