Changing from a Vertical Burr to a Horizontal Burr in the Vertical-Type High-Speed Twin-Roll Caster

Toshio Haga; Yushi Murakami; Shou Kitamura; Hisaki Watari; Shinichi Nishida

doi:10.4028/www.scientific.net/MSF.1007.29

Paper Titles

Reduction of Surface Cracks at Al-Mg Alloy Strip Surface Cast by Unequal Diameter Twin Roll Caster
p.6

Roll Casting and Die Casting of Si-Added Al-Mg Alloy
p.12

Effect of Si and Mn Addition on Fluidity, Mechanical Property and Casting Crack in Die Casting
p.18

Casting of Clad Strip Consisting of Al-Sn Alloy and Pure Aluminum
p.23

Changing from a Vertical Burr to a Horizontal Burr in the Vertical-Type High-Speed Twin-Roll Caster
p.29

Globular Crystals in the Center of Roll Cast Aluminum Alloy Strips
p.34

Effect of Alloying Elements on Mechanical Properties of High-Strength Low-Alloy Steel
p.41

Effect of Synthesis Conditions on the Preparation of Ag/ZnTiO₃ via Sol-Gel Method and its Antibacterial Properties
p.47

Pebax 1657 Nanocomposite Membranes Incorporated with Nanoadsorbent Derived from Oil Palm Frond for CO₂/CH₄ Separation
p.52

HomeMaterials Science ForumMaterials Science Forum Vol. 1007Changing from a Vertical Burr to a Horizontal Burr...

Changing from a Vertical Burr to a Horizontal Burr in the Vertical-Type High-Speed Twin-Roll Caster

Abstract:

Strip casting using a side dam plate produces a vertical burr at the strip edge. In the present study, changing this vertical burr into a horizontal burr using a burr changer is proposed. The burr changer was placed inside the side dam plate. The burr changer was made from mild steel and an insulator sheet and cut along the shape of the roll. The burr changer was placed so as to prevent exhaustion of semisolid metal between the side dam plate and the roll-side surface. When the position of the burr changer was appropriate, the vertical burr changed into a horizontal burr. The horizontal burr was flat. The width of the horizontal burr was affected by the lowest position of the burr changer and became narrower as the lowest position of the burr changer approached the roll gap position.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volume 1007)

Pages:

29-33

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.1007.29

Citation:

Cite this paper

Online since:

August 2020

Authors:

Toshio Haga*, Yushi Murakami, Shou Kitamura, Hisaki Watari, Shinichi Nishida

Keywords:

Burr Changer, Horizontal Burr, Vertical Burr, Vertical Type High Speed Twin Roll Caster

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] T. Haga, T. Yamashiki, H. Watari, S. Niahida: Investigation of Burr on Strips Cast by Vertical-Type High-Speed Twin Roll Caster, Key Engineering Materials 831(2020) 40-45.

DOI: 10.4028/www.scientific.net/kem.831.40

Google Scholar

[2] T. Haga: submitted to Key Engineering Materials (2019).

Google Scholar

[3] T. Haga, K. Takahashi, H. Watari, Semisolid strip casting using a vertical type twin roll caste, Mater. Sci. Forum, 426(1) (2003) 477-482.

DOI: 10.4028/www.scientific.net/msf.426-432.477

Google Scholar

[4] T. Haga, K. Takahashi, M. Ikawa, H. Watari, A vertical type twin roll caster for aluminum alloy strip, J. Mater. Proce. Technol. 140(1-3) (2003) 610-615.

DOI: 10.1016/s0924-0136(03)00835-5

Google Scholar

[5] T. Haga, K. Takahashi, M. Ikaw, H. Watari, Twin roll casting of aluminum alloy strips, J. Mater. Proce. Technol. 153-154 (2004) 42-47.

DOI: 10.1016/j.jmatprotec.2004.04.018

Google Scholar

[6] T. Haga, A high speed twin roll caster for aluminum alloy thin strip, Trans. Mater. Res. Soc. Japan, 29(5) (2004) 1823-1828.

DOI: 10.1299/jsmeintmp.2005.2_5

Google Scholar

[7] R. Nakamura, H. Watari, S. Kumai, High speed roll casting of aluminum alloy strip, Mater. Sci. Forum, 475-479 (2005) 343-348.

DOI: 10.4028/www.scientific.net/msf.475-479.343

Google Scholar

[8] T. Haga, H. Watari, S. Kumai, High speed roll casting of Mg alloy strip by a vertical type twin roll caster, J. Ach. Mater. Manuf. Eng. 15(1-2) (2006) 186-192.

DOI: 10.1299/jsmeintmp.2005.2_5

Google Scholar

[9] T. Haga, T. Nakamura, S. Kumai, H. Watari, Roll casting of Al-SiCp strip, Mater. Sci. Forum, 675-677 (2011) 811-814.

DOI: 10.4028/www.scientific.net/msf.675-677.811

Google Scholar

[10] T. Haga, Development of a twin roll caster for light metal, J. Ach. Mater. Manuf. Eng. 43(1) (2010) 393-402.

Google Scholar