Mechanical and Thermal Properties of Harmonic Structured Composites by MM/SPS Process

Abstract:

Harmonic structured composites consist of a low fraction metal region like network and a dispersed another major metal region like island. The harmonic structured composites were produced via mechanical milling (MM) followed by spark plasma sintering (SPS), and its mechanical and thermal properties were investigated in detail. Microstructural observation of the MM powders and SPS compacts was achieved using scanning electron microscopy (SEM). The mechanical properties of the harmonic structured composites were evaluated using results of the Vickers hardness and the tensile tests. The thermal properties of a part of the harmonic structured composites were evaluated using results of thermo-mechanical analysis and laser flash method. High speed steel / mild steel harmonic structured composite exhibited high strength and enough ductility in spite of the trade-off relationship between strength and ductility. In addition, the high speed steel / mild steel harmonic structured composite also demonstrates a superior wear properties and low hardness simultaneously. On the other hand, molybdenum / copper harmonic structured composite demonstrate low coefficient of linear expansion and enough thermal conductivity compared to the conventional copper / molybdenum particle dispersed composite. The coefficient of linear expansion and thermal conductivity are the trade-off relation in this composite. In summary, the harmonic structure control is effective for improvement of the trade-off mechanical and thermal properties in the composite.

• Periodical: Materials Science Forum (Volume 1016)
• Pages: 113-118
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1016.113
• Online since: January 2021
• Authors: Hiroshi Fujiwara*
• Keywords: Harmonic Structure, Mechanical Milling, Powder Metallurgy, Spark Plasma Sintering

References

[1] N. Tsuji, N. Kamikawa, R. Ueji, N. Takata, H. Koyama and D. Terada: ISIJ Int., 48 (2008), 1114–1121.

DOI: 10.2355/isijinternational.48.1114

[2] N. Tsuji, Y. Ito, Y. Saito and Y. Minamino: Scripta Mater., 47(2002), 893-99.

[3] T. Sekiguchi, K. Ono, H. Fujiwara and K. Ameyama: Mater. Trans., 51 (2010), 39-45.

[4] H. Fujiwara, R. Akada, A. Noro, Y. Yoshita and K. Ameyama: Mater. Trans., 49 (2008), 90-96.

DOI: 10.2320/matertrans.me200703

[5] H. Fujiwara, T. Sekiguchi and K. Ameyama: Int. J. Mater. Res., 100(2009), 769-799.

[6] K. Ameyama and H. Fujiwara: Mater. Sci. Forum, 706-709(2012), 9-16.

[7] Y. Yamada, H. Fujiwara, H. Miyamoto and K. Ameyama: J. Jpn. Soc. Powder Powder Metallurgy, 60 (2013) 160-166.

[8] T. Takahashi, T. Abe, T. Sakurai and Y. Mizutani: Tohoku Kogyo-gijyutu-sikenjyo Houkoku, 15 (1982) 28-31.

[9] Y. Shimizu: J. Jpn. Soc. Tribol., 52 (2007) 107-113.

[10] K. Notomi and N. Kawai: J. Jpn. Soc. Powder Powder Metallurgy, 36 (1989) 87-92.

[11] T. Shinoda, S. Kang, H. Jeong and Y. Kato: J. Jpn. Inst. Light Met., 49 (1999) 432-437.

[12] A. Wakigawa, S. Aiyoshizawa, K. Takagi and D. Konno: Trans. Jpn. Soc. Mech. Eng. Series B, 53(1987) 2094-2098.

[13] H. Fujiwara, Y. Tsuzuki and H. Miyamoto: J. Jpn. Soc. Powder Powder Metallurgy, 62 (2015) 302-307.

[14] Ametek, Molybdenum-Copper Composite AMC 3169, MatWeb, (reference Dec. 8, 2017). http://www.matweb.com/index.aspx.