Main Alloying Influence on Second Phase Dissolution during Solution Treatment of Al-Zn-Mg-Cu Alloys

Abstract:

Second phase dissolution of Al-Zn-Mg-Cu alloys during solution treatment was closely associated with the content of main alloying elements. In present work, the phase characteristics of several Al-Zn-Mg-Cu alloys with various main alloying contents were investigated, and the second phase dissolution of these alloys during solution treatment was analyzed. The results showed that the extrusion alloys possessed abundant second phases, mainly including Mg(Zn,Cu,Al)₂ phase and Fe-rich particles. The DSC analysis proved that the larger endothermic peak corresponded to the alloy with larger main alloying content, and the XRD spectrogram also backed up the advantage of Mg(Zn,Cu,Al)₂ phase. After solution treated at 450°C, the residual phases remained in the alloys and the quantity of them were positively correlated with the main alloying content. With the increase of solution temperature, the electrical conductivity of the alloys showed a decremental trend, while the alloys with relatively low main alloying contents exhibited an inversion at the solution temperature of 475°C. The SEM observation demonstrated that no Mg(Zn,Cu,Al)₂ phase was observed in the alloys with relatively low main alloying contents while seldom still remained in the alloy with high main alloying content after solution treated at 470°C. After solution treated at 475°C, Mg(Zn,Cu,Al)₂ phase completely dissolved into the matrix for the alloy with high main alloying content. The statistics of residual phase quantity also proved this.

• Periodical: Materials Science Forum (Volume 1035)
• Pages: 3-9
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.1035.3
• Online since: June 2021
• Authors: Hong Wei Liu, Kai Wen*, Wei Cai Ren, Xi Wu Li, Yong An Zhang, Zhi Hui Li, Bai Qing Xiong
• Keywords: Al-Zn-Mg-Cu Alloy, Main Alloying, Second Phase Dissolution, Solution Treatment

References

[1] A. Heinz, A. Haszler, C. Keidel, et al. Recent development in aluminium alloys for aerospace applications, Mater. Sci. Eng. A. 2000, 280(1): 102-107.

DOI: 10.1016/s0921-5093(99)00674-7

[2] T. Dursun, C. Soutis. Recent developments in advanced aircraft aluminium alloys, Mater. Des. 2014, 56(4): 862-871.

DOI: 10.1016/j.matdes.2013.12.002

[3] I.J. Polmear. Aluminium Alloys – A Century of Age Hardening, Mater. Forum. 2004, 28: 1-14.

[4] P.A. Rometsch, Y. Zhang, S. Knight. Heat treatment of 7xxx series aluminium alloys—Some recent developments, Trans. Nonferrous Metals Soc. 2014, 24(7): 2003-2017.

DOI: 10.1016/s1003-6326(14)63306-9

[5] G. Wang, Z. Zhao, Y. Zhang, et al. Effects of solution treatment on microstructure and mechanical properties of Al-9.0Zn-2.8Mg-2.5Cu-0.12Zr-0.03Sc alloy, T. Nonferrous Metals Soc. 2013, 23(9): 2537-2542.

DOI: 10.1016/s1003-6326(13)62765-x

[6] N.E. Mazibuko, U.A. Curle. Effect of Solution Heat Treatment Time on a Rheocast Al-Zn-Mg-Cu Alloy, Mater. Sci. Forum 2011, 690: 343-346.

DOI: 10.4028/www.scientific.net/msf.690.343

[7] X. Fa, D. Jiang, Q. Meng, et al. Evolution of eutectic structures in Al-Zn-Mg-Cu alloys during heat treatment, T. Nonferrous Metals Soc. 2006, 16(3): 577-581.

DOI: 10.1016/s1003-6326(06)60101-5

[8] D. Xu, P. Rometsch, N. Birbilis, et al. Improved solution treatment for an as-rolled Al-Zn-Mg-Cu alloy. Part I. Characterization of constituent particles and overheating, Mater. Sci. Eng. A. 2012, 534: 234-243.

DOI: 10.1016/j.msea.2011.11.065

[9] N. Han, X. Zhang, S. Liu, et al. Effect of solution treatment on the strength and fracture toughness of aluminum alloy 7050, J. Alloys Compd. 2011, 509(10): 4138-4145.

DOI: 10.1016/j.jallcom.2011.01.005

[10] H.C. Fang, H. Chao, K.H. Chen. Effect of recrystallization on intergranular fracture and corrosion of Al–Zn–Mg–Cu–Zr alloy,J. Alloys Compd. 2015, 622: 166-173.

DOI: 10.1016/j.jallcom.2014.10.044

[11] P. Li, B. Xiong, Y. Zhang, et al. Temperature variation and solution treatment of high strength AA7050,T. Nonferrous Metals Soc. 2012, 22(3): 546-554.

DOI: 10.1016/s1003-6326(11)61212-0

[12] Z. Wu, H. Bei, F. Otto, et al. Recovery, recrystallization, grain growth and phase stability of a family of FCC-structured multi-component equi-atomic solid solution alloys, Intermetallics. 2014, 46: 131-140.

DOI: 10.1016/j.intermet.2013.10.024

[13] K. Chen, H. Liu, Z. Zhang, et al. The improvement of constituent dissolution and mechanical properties of 7055 aluminum alloy by stepped heat treatments,J. Mater. Process. Tech. 2003, 142(1): 190-196.

DOI: 10.1016/s0924-0136(03)00597-1

[14] T.A. Costa, M. Dias, L. Gomes, et al. Effect of solution time in T6 heat treatment on microstructure and hardness of a directionally solidified Al–Si–Cu alloy,J. Alloys Compd. 2016, 683: 485-494.

DOI: 10.1016/j.jallcom.2016.05.099