An Artificial Neural Network Model for the Stress Concentration Factors in KT-Joints Subjected to Axial Compressive Load

Abstract:

Stress concentration factor (SCF) is usually used to estimate the fatigue life of an offshore joint. Historically, parametric equations were used to estimate SCF based on a statistical analysis of experimental and finite element analysis (FEA) results, to reduce cost and time. These equations give the SCF at the saddle/crown position for simple joints and basic load cases. However, for modified or defective joints, the location of the maximum SCF can change. In such circumstances, the single-point SCF equation cannot be used to estimate the maximum value of SCF, as its location may have changed from saddle/crown. To our knowledge, there are no general expressions to estimate SCF around the brace axis accurately. As artificial neural networks (ANN) can approximate the trend of complex phenomena better than conventional data fitting, a mathematical model based on ANN is proposed to estimate SCF based on the weights and biases of trained ANN. Nine hundred thirty-seven finite element simulations were performed to generate SCF data for training the ANN. This ANN was used to model an empirical equation for SCF. The proposed empirical model can estimate SCF around the brace axis with less than 5% error. The current study provides a roadmap to using FEA and ANN for empirical modeling of SCF in tubular joints, and this approach can be applied to any joint type, with or without design modification or damage. Once a database of similar equations is available, it can be utilized for quickly estimating SCF instead of costly experimentation and FEA. Optimization of the ANN can further improve the accuracy of the developed mathematical model.

• Periodical: Materials Science Forum (Volume 1103)
• Pages: 163-175
• DOI: https://doi.org/10.4028/p-YpO50i
• Online since: October 2023
• Authors: Mohsin Iqbal*, Saravanan Karuppanan, Veeradasan Perumal, Mark Ovinis, Akram Hina
• Keywords: Artificial Neural Networks, Empirical Modeling, Finite Element Analysis, Kt-Joint, Stress Concentration Factor

References

[1] H. Ahmadi, M. A. Lotfollahi-Yaghin, and M. H. Aminfar, "Effect of stress concentration factors on the structural integrity assessment of multi-planar offshore tubular DKT-joints based on the fracture mechanics fatigue reliability approach," Ocean Eng., vol. 38, no. 17–18, p.1883–1893, 2011.

DOI: 10.1016/j.oceaneng.2011.08.004

[2] X. Xu, Y. Shao, X. Gao, and H. S. Mohamed, "Stress concentration factor (SCF) of CHS gap TT-joints reinforced with CFRP," Ocean Eng., vol. 247, December 2021, p.110722, 2022.

DOI: 10.1016/j.oceaneng.2022.110722

[3] S. Petinov and R. Guchinsky, "Criteria for Fatigue Failure of Materials: Application in Fatigue Assessment of Structures," Adv. Eng. Forum, vol. 26, p.1–8, 2018.

DOI: 10.4028/www.scientific.net/aef.26.1

[4] A. B. Potvin, J. G. Kuang, R. D. Leick, and J. L. Kahlich, "Stress Concentration in Tubular Joints," Soc. Pet. Eng., p.287–299, 1977.

DOI: 10.2118/5472-pa

[5] A. C. Wordsworth, "Stress Concentration Factors at K and KT tubular joints," in Fatigue in Offshore Structural Steels, 1981, p.59–66.

[6] M. Efthymiou, "Development of SCF formulae and generalized influence functions for use in fatigue analysis," in Recent Developments in Tubular Joints Technology (OTJ 88), 1988.

[7] Lloyd's Register, "Stress Concentration Factors for Simple Tubular Joints," Lloyd's Regist. Shipp. Heal. Saf. Exec. Technol. Repor (OTH 354), 1997.

[8] Lloyd's Register, "Stress Concentration Factors for Tubular Complex Joints," Lloyd's Regist. Shipp. Heal. Saf. Exec. - Offshore Technol. Rep. (OTH 91 353), 1992.

[9] S. Bao, W. Wang, X. Li, S. Qi, and J. Zhou, "Experimental study of hot spot stress for three-planar tubular Y-joint: II. Combined loads," Thin-Walled Struct., vol. 177, March, p.109416, 2022.

DOI: 10.1016/j.tws.2022.109416

[10] I. Mohsin, K. Saravanan, P. Veeradasan, O. Mark, and N. Hina, "Empirical modeling of stress concentration factors using FEA and artificial neural networks for the fatigue design of tubular KT-joints under combined loading," Fatigue Fract. Eng. Mater. Struct., August, 2023.

[11] M. Iqbal, S. Karuppanan, V. Perumal, and M. Ovinis, "Rehabilitation Techniques for Offshore Tubular Joints," J. Mar. Sci. Eng., vol. 11, p.461, 2023, doi: https://doi.org/.

DOI: 10.3390/jmse11020461

[12] S. H. Han, J. W. Han, and Y. Y. Nam, "Fatigue life improvement using mechanical post treatment for weldment," Mater. Sci. Forum, vol. 580–582, p.97–100, 2008.

DOI: 10.4028/www.scientific.net/msf.580-582.97

[13] M. Farajian, T. Nitschke-Pagel, and K. Dilger, "Welding residual stresses in tubular joints," Mater. Sci. Forum, vol. 768–769, p.605–612, 2014.

DOI: 10.4028/www.scientific.net/MSF.768-769.605

[14] M. A. Lotfollahi-Yaghin and H. Ahmadi, "Effect of geometrical parameters on SCF distribution along the weld toe of tubular KT-joints under balanced axial loads," Int. J. Fatigue, vol. 32, no. 4, p.703–719, 2010.

DOI: 10.1016/j.ijfatigue.2009.10.008

[15] H. Ahmadi, Lotfollahi-Yaghin, and A. Mohammad, "Experimental and Numerical Investigation of Geometric SCFs in Internally Ring-Stiffened Tubular KT-Joints of Offshore Structures," J. Persian Gulf, vol. 4, no. 12, p.1–12, 2013.

DOI: 10.1016/j.apor.2012.07.004

[16] A. Sadat Hosseini, E. Zavvar, and H. Ahmadi, "Stress concentration factors in FRP-strengthened steel tubular KT-joints," Appl. Ocean Res., vol. 108, February, p.102525, 2021.

DOI: 10.1016/j.apor.2021.102525

[17] E. Zavvar, A. Sadat Hosseini, and M. A. Lotfollahi-Yaghin, "Stress concentration factors in steel tubular KT-connections with FRP-Wrapping under bending moments," Structures, vol. 33, July, p.4743–4765, 2021.

DOI: 10.1016/j.istruc.2021.06.100

[18] K. Miao, Z. Pan, A. Chen, Y. Wei, and Y. Zhang, "Machine learning-based model for the ultimate strength of circular concrete-filled fiber-reinforced polymer–steel composite tube columns," Constr. Build. Mater., vol. 394, May, p.132134, 2023.

DOI: 10.1016/j.conbuildmat.2023.132134

[19] S. D. Vijaya Kumar, S. Karuppanan, V. Perumal, and M. Ovinis, "Failure Pressure Prediction of Corroded High-Strength Steel Pipe Elbow Subjected to Combined Loadings Using Artificial Neural Network," Mathematics, vol. 11, no. 7, 2023.

DOI: 10.3390/math11071615

[20] M. Dabiri, M. Ghafouri, H. R. R. Raftar, and T. Björk, "Neural network-based assessment of the stress concentration factor in a T-welded joint," J. Constr. Steel Res., vol. 128, p.567–578, 2017.

DOI: 10.1016/j.jcsr.2016.09.024

[21] E. Zavvar, J. Henneberg, and C. Guedes Soares, "Stress concentration factors in FRP-reinforced tubular DKT joints under axial loads," Mar. Struct., vol. 90, February, p.103429, 2023.

DOI: 10.1016/j.marstruc.2023.103429

[22] B. Jardine, "Fatigue Life Enhancement of Tubular Joints By Grout Injection," 1993. doi: 0-7176 0613 9.

[23] S. D. Vijaya Kumar, M. Lo, S. Karuppanan, and M. Ovinis, "Empirical Failure Pressure Prediction Equations for Pipelines with Longitudinal Interacting Corrosion Defects Based on Artificial Neural Network," J. Mar. Sci. Eng., vol. 10, no. 6, 2022.

DOI: 10.3390/jmse10060764

[24] ARSEM (Association de recherche sur les structures métalliques marines), Welded tubular joints-Design guides for offshore structures, vol. 1. Technip, Peris France, 1987.

[25] International Standard Organization, "Petroleum and natural gas industries — Fixed steel offshore structures (ISO-19902)," 2007. [Online]. Available: www.iso.org

[26] H. Ahmadi and A. Z. Nejad, "Stress Concentration Factors in Uniplanar Tubular KT-Joints of Jacket Structures Subjected to In-Plane Bending Loads," Int. J. Marit. Technol. IJMT, vol. 5, p.27–39, 2016, [Online]. Available: http://ijmt.ir/browse.php?a_code=A-10-296-4&sid=1&slc_lang=en

DOI: 10.1016/j.tws.2015.02.011

[27] H. Ahmadi, "Probabilistic analysis of the DoB in axially-loaded tubular KT-joints of offshore structures," Appl. Ocean Res., vol. 87, February, p.64–80, 2019.

DOI: 10.1016/j.apor.2019.03.018