Microstructure and Texture Evolution of Fe-Si Steels after Hot Dipping and Diffusion Annealing

Abstract:

A homogenous intensity distribution along the cube texture fibre is important to achieve an easy magnetization in non-oriented electrical steels. Several alternatives have been discussed in literature to achieve this goal namely, tertiary recrystallization (surface energy controlled), decarburization annealing, two step cold rolling (strain induced boundary migration), twin-roll thin strip casting (directional solidification), phase transformation (surface energy anisotropy) and columnar grains formation (selective grain growth). In the present study, a hypoeutectic Al-Si alloy was deposited on the surface of cold rolled Fe-Si steels with a hot dipping simulator and subsequently annealed at 1000°C for different times. This procedure was developed previously in order to enrich the substrate with Al and/or Si and consequently improve their resistivity. Of specific interest was the formation of columnar grains in the low Fe-Si steel after annealing. These columnar grains were found to grow from the surface towards the centre of the substrate. The microstructure and texture in the columnar grains were significantly different than those in the middle of the material. Therefore, the evolution of these features during processing was studied in detail in this work.

• Periodical: Materials Science Forum (Volumes 706-709)
• Pages: 2628-2633
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.706-709.2628
• Online since: January 2012
• Authors: I. Infante Danzo, Kim Verbeken, Yvan Houbaert
• Keywords: Columnar Grains, Diffusion Annealing, Fe-Si Steels, Hot Dipping, Texture Development

References

[1] J.L. Walter, W.R. Hibbard; H.C. Fiedler, H.E. Grenoble, R.H. Pry and P.G. Frischmann. Magnetic Properties of Cube Textured Silicon-Iron Magnetic Sheet. J. Appl. Phys Vol. 29 (1958), p.363.

DOI: 10.1063/1.1723135

[2] Toshiro. Tomida, Shigeo. Uenoya and Naoyuki. Sano, Fine-Grained Doubly Oriented Silicon Steel Sheets and Mechanism of Cube Texture Development. Mater. Trans. Vol. 44 (2003), p.1106.

DOI: 10.2320/matertrans.44.1106

[3] F. Kovác, M. Dzubinský and Y. Sidor, Columnar Grain Growth in Non-Oriented Electrical. Steels. J. Mag. Mag. Mater. Vol. 269 (2004), p.333.

[4] R.G. Aspden, J. A. Berger and H. E. Trout, Anisotropic and Heterogeneous Nucleation During the Gamma to Alpha Transformation in Iron. Acta Met. Vol. 16 (1968), p.1027.

DOI: 10.1016/0001-6160(68)90091-6

[5] Y. Sidor, F. Kovac and T. Kvackaj, Grain Growth Phenomena and Heat Transport in Non-Oriented Electrical Steels. Acta Mater. Vol. 55 (2007), p.1711.

DOI: 10.1016/j.actamat.2006.10.032

[6] P. Van Houtte, The MTM-FHM Software System Version 2 Users Manual (1995).

[7] Cheng. Wei-Jen and Wang. Chaur-Jeng, Growth of Intermetallic Layer in the Aluminide Mild Steel During Hot-Dipping. Surf. Coat. Technol. vol 204 (2009), p.824.

DOI: 10.1016/j.surfcoat.2009.09.061

[8] I. Infante Danzo, K. Verbeken and Y. Houbaert, Microstructure of Hot Dip Coated Fe-Si Steels. Submitted to 38th International Conference On Metallurgical Coatings and Thin Films (2011).

DOI: 10.1016/j.tsf.2011.07.042

[9] Toshiro. Tomida and Takashi. Tanaka, Development of (100) Texture in Silicon Steel Sheets by Removal of Manganese and Decarburization. ISIJ Interna. Vol. 35 (1995), p.548.

DOI: 10.2355/isijinternational.35.548

[10] K. Verbeken, L. Kestens and J.J. Jonas, Microtextural Study of Orientation Change During Nucleation and Growth in a Cold Rolled ULC Steel, Scripta Mater. Vol. 48 (2003), p.1457.

DOI: 10.1016/s1359-6462(03)00078-2

[11] J. Gautam, R. Petrov, L. Kestens and E. Leunis. Surface Energy Controlled alpha-gamma-alpha Transformation Texture and Microstructure Character Study in ULC Steels Alloyed with Mn and Al. J. Mater. Sci. Vol. 43 (2008), p.3969.

DOI: 10.1007/s10853-007-2292-4