Study on the Flow Field of Friction Stir Welding of AZ31 Magnesium Alloy Based on the Temperature Variation

Abstract:

In this study, AZ31 magnesium alloy plates were butt welded by friction stir welding to investigate the flow field characterization, and temperature variation was measured. “Marker insert technology” and “stitch welding of dissimilar materials technique” were used to make the flow field visualization. The results indicated that both the temperature variation and the flow way of material are three dimensional asymmetric. In terms of temperature distribution, along the welding direction, the temperature is gradually increased during the process; along the thickness direction, the peak temperature is high in the upper part and low in the lower; perpendicular to the welding direction, the peak temperature of the advancing side is slightly higher than the retreating side. In terms of the flow field, the flow way of the material in the advancing side is different from retreating side. Material from the advancing side crosses the pin and is divided into two directions: part is dragged forward by the shoulder while part is extruded backward. However, materials in retreating side move backward only. At different depths, the flow range of plastic material is different. The closer to the bottom of the weld, the flow range of plastic material is smaller. Along the welding direction, the flow range of the plastic material changes larger from the initial stage to the end stage. On the cross section of the weld, plastic material that adjacent to the pin is squeezed down while part of the material at the bottom is forced to move upwards. The rising material converged with the downward current and formed a cycle. Considering the deformation tendency of the lapped surface, the advancing side is more intense than the retreating side.

• Periodical: Materials Science Forum (Volume 789)
• Pages: 282-289
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.789.282
• Online since: April 2014
• Authors: Ali Lu*, Sheng Lu, Shu Jin Chen, Dai Li Yang
• Keywords: Flow Field, Friction Stir Welding (FSW), Overlay Welding of Dissimilar Materials, Tags Embedded Technology, Temperature Distribution

References

[1] W. B. Wang, W. Wang, D. L. Wang et al. Analysis on the temperature field of Aluminum alloy in the initial state of friction stir welding [J]. Hot Working Technology, 2008, 37(21):107-109,113.

[2] H. Zhang, S. B. Lin, L. Wu et al. Numerical simulation of the temperature field of friction stir welding of AZ31 magnesium alloy [J]. Aerospace Materials & Technology, 2004, 34(6):58-61.

[3] X. J. Wang, X. H. Han, R. J. Guo et al. Numerical simulation of the temperature field of friction stir welding [J]. Journal of welding, 2005, 26(12):17-20.

[4] M. Guerra, C. Schmidt, J. C. McClure et al. Flow pattern during Friction Stir Welding [J]. Materials Characterization, 2003, 49:95s-101s.

[5] K. Colligan. Material flow behavior during Friction Stir Welding of Aluminum [J].Welding Journal, 1999, 78(7):229s-237s.

[6] W. Zhang, N. M. Ke, L. Xing et al. Analysis of the transfer behavior of material on cross-section of friction stir welding [J]. Materials engineering, 2008, (2):62-66.

[7] T. U. Seidel, A. P. Reynolds. A two-dimensional Friction Stir Welding Process Model Based on Fluid Mechanics [J].Science and Technology of Welding and Joining, 2003, 8:175s-183s.

DOI: 10.1179/136217103225010952

[8] X. J. Wang, X. H. Han, C. F. Li et al. The study on the flow of plastic material in different depth of thick aluminum plates along the horizontal direction [J]. Chinese Journal of nonferrous metals, 2005, 15(2):198-204.

[9] X. J. Wang, X. H. Han, C. F. Li et al. The study on the flow of plastic material in different depth of thick aluminum plates along the thickness direction [C].2004 The International Forum on aerospace welding technology.2004:328-333.

[10] X. J. Wang, X. H. Han. Three dimension numerical simulation of friction stir welding of aluminum alloy based on fluent [J]. Electric Welding Machine, 2006, 36(1):48-50.

[11] X. H. Han, X. J. Wang. Flow field of friction stir welding of aluminum alloy along the thickness direction [J]. Electric Welding Machine, 2006, 36(11):48-52.

[12] X. H. Han, X. J. Wang. Flow field of friction stir welding of aluminum alloy along the horizontal direction [J]. Electric Welding Machine, 2006, 36(3):52-54.

[13] M. Xiao. Research on the microstructure and thermal deformation behavior of the AZ31 magnesium alloy [D]. Dissertation of master degree of Chongqing University.2009:27-48.