Mathematical Model of Temperature Conditions of Sheet Mills with Furnace Coilers

Abstract:

Determining the temperature of the strip at certain points in the technological line of the mill is very important problem in the development of new and optimization of existing technologies of the sheet rolling process. This article proposes a mathematical model of the temperature conditions of strip rolling on a mill with furnace coilers. The model takes into account the temperature change in the deformation zone during rolling, during transportation of the strip in the mill line, as well as in heating devices, in particular, in the furnaces of coilers of the Steckel mill. It is possible to calculate the change in temperature of the strip on coils and the surface of strip wind up in roll when the coiler furnaces. The mathematical model can be used for engineering calculations, as well as a tool for the scientific analysis of technological processes of sheet rolling.

• Periodical: Materials Science Forum (Volume 989)
• Pages: 711-718
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.989.711
• Online since: May 2020
• Authors: M.A. Sosedkova*, A.S. Grigorenko, L.V. Radionova, Tat'yana A. Lisovskaya, Viacheslav D. Lezin
• Keywords: Furnace Winders, Sheet Hot Rolling, Steckel Mill, Temperature Conditions

References

[1] Y.V. Konovalov, Ways to solve the rolling temperature problem, in: Y.V. Konovalov, A.S. Hohlov, Pressure treatment: a collection of scientific papers, DSEA, Kramatogorsk, 2012, pp.185-188.

[2] A.P. Grudev, L.F. Mashkin, M.I. Khanin, Rolling technology: textbook for universities, Metallurgy, Moscow, (1994).

[3] V.P. Poluhin, Mathematical modeling and computer calculations of sheet mills, Moscow, Metallurgy, (1972).

[4] V.A. Osadchin, V.T. Zhdanov, O.Y. German, Applying information technologies in the study of methods of calculation of technological parameters of the rolling process, Rolling production. 11 (2000) 40-43.

[5] A.L. Genkin, Information on energy-power parameters in controlling the temperature-speed mode of hot-rolled strip, Automation in industry, 8 (2009) 45-48.

[6] L.V. Radionova, Y.V. Buzhlanov, Application of mathematical models for prediction of microstructure and mechanical properties of rods of high carbon steel grades, MSTU Newsteller, 24 (2008) 73-75.

[7] L.V. Radionova, O.A. Sarapulov, Mathematical model of rod cooling in a small section mill, Science and manufacture of the Urals, 10 (2014) 171-174.

[8] B.A. Dubrovskiy, B.A. Nikiforov, V.A. Kharitonov, L.V. Radionova, Mathematical modeling of the temperature field of round bars on the thermal hardening line of the rolling mill, Vestnik of Magnitogorsk State Technical University named after G.I. Nosov, 3 (2005) 53-58.

[9] V.M. Salganikov Y.A. Tverskoy, A.V. Kushnarev, A.G. Soloviev, S.V. Denisov, A.A. Mastruev, Y.V. Kudriakov, A.A. Radionov, Possibilities and options for upgrading MMK's 2500 broadband mill for controlled hot-rolling, Ferrous metallurgy, 1 (2002) 37-38.

[10] V.R. Gasiyarov, Automatic control of the rolling geometry on a 5000 hot-rolled plate mill, in: V.R. Gasiyarov, D.Y. Usatiy, A.A. Radionov, L.V. Radionova, Fourth All-Russian Multi-Conference on Management Problems MCMP-2011, materials of the 4th All-Russian Multi-Conference, Taganrog, 2011, pp.307-308.

DOI: 10.1109/rusautocon.2018.8501803

[11] I.A. Serdiuk, A.S. Khadzhinov, S.G. Dvornikov, A.A. Kholodnyi, A.G. Prisiazhnyi, Mathematical model of calculating the temperature of rolling in the process of hot sheet rolling by the method of criterial equations, Bulletin of the Pryazovskyi State Technical University. Series of «Technical Sciences», PSTU, Mariupol. 2(23) (2011).

[12] M.A. Zaikov, V.P. Polukhin, A.M. Zaikov, L.N. Smirnov, Rolling process, MISIS, Moscow, (2004).

[13] A.R. Gareev, S.A. Murikov, S.I. Platov etc., The heat balance of the rolling stock on a broadband hot rolling mill, Modeling and development of metal forming processes, NMSTU, Magnitogorsk, 20 (2014) 250-258.

[14] L.V. Radionova, R.A. Lisovskii, T.A. Lisovskaia, Computer simulator Cold rolling of sheet steel,: Mathematical modeling of the process and 3D visualization of equipment, Russian Internet Journal of Industrial Engineering. 4(1) (2016) 29-39.

DOI: 10.24892/rijie/20160206

[15] M.M. Safian, V.L. Mazur, A.M. Safian, A.I. Molchanov, Technology of rolling and drawing processes, Sheet-rolling production, Vyshcha shkola, (1988).

[16] A.I. Tselikov, A.D. Tomlenov, V.I. Ziuzin, Theory of rolling, Metallurgy, Moscow, (1982).

[17] S.L. Kotsar, A.D. Belianskii, Iu.A. Mukhin, Sheer rolling production technology, Metallurgy, Moscow, (1997).

[18] F.S. Dubinskiy, M.A. Sosedkova, Temperature simulation to optimize long product rolling, New technologies and achievements in metallurgy, material engineering and production engineering: XIN International scientific conference, Czestochowa, (2013).

[19] M.A. Sosedkova, L.V. Radionоva, T.A. Lisovskaya, Mathematical model of hot rolling temperature parameters, Solid State Phenomena, 265 (2017) 1026–1033.

DOI: 10.4028/www.scientific.net/ssp.265.1026

[20] H. Wenzel, Rolling and rolling equipment, VINITI, Express information, 27 (1965) 8-43.