Processing Methods Used to Create High-Quality Porous Structure of Aerated Concrete

Abstract:

The efficiency of porous structure formation in aerated concrete can be improved by including the methods of thermal vacuum compaction or thermal vacuum compaction with vibration into the process as a means of creating high-quality composite cellular concrete. A graphic model of a phase composition change in the aerated concrete mix was developed allowing for an evaluation of the recipe and the mode of bubble porosity generation during hardening. This provides a control over the manufacturing processes and helps to produce aerated concrete with the specified porosity balance, which defines product properties.The effect of temperature and vacuum on molding sand during the initial stage of manufacture is proportional to the bubble porosity volume, which is important for a high-quality porous structure formation. In addition to the above, account must be taken of the combined effect of temperature, vacuum and volume ratio of phases in the base mix when using the proposed methods.Introduction of the developed processing methods into the manufacturing process improves the technology of aerated concrete production and allows for a fabrication of the finest advanced heat insulating and structural and heat insulating products.

• Periodical: Materials Science Forum (Volume 992)
• Pages: 212-217
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.992.212
• Online since: May 2020
• Authors: L.A. Suleymanova*, A.S. Kolomatsky, M.V. Marushko
• Keywords: Aerated Concrete, Porous Structure, Process Control, Processing Methods, Thermal Vacuum Compaction, Thermal Vacuum Compaction with Vibration

References

[1] A.A. Vishnevsky, G.I. Greenfeld, A.S. Smirnova, The current state of production of autoclaved aerated concrete in Russia, Collection of reports of scientific and practical. Conference Modern Autoclaved Aerated Concrete,, Yekaterinburg, 2017, 10-12.

DOI: 10.31659/0585-430x-2018-757-3-62-64

[2] N.P. Sazhnev, Experience in the production and use of autoclaved aerated concrete. Theory and Practice, Strinko, Minsk, (2010).

[3] E.I. Batyanovsky, Manufacture of autoclaved aerated concrete products, Strinko, Minsk, (2009).

[4] M.I. Seifman, Production of silicate brick and silicate cellular materials, Stroyizdat, Moscow, (1990).

[5] C.V. Leontiev, V.A. Shamanov, A.D. Kurzanov, Studying the influence of prescription and technological factors on the processes of formation of the structure and properties of low density autoclaved aerated concrete, Collection of reports of scientific and practical. Conference Modern Autoclaved Aerated Concrete,, Yekaterinburg, 2017, 39-47.

DOI: 10.14359/14389

[6] A.A. Vishnevsky, G.I. Greenfeld, Choice of technology for the production of autoclaved aerated concrete: percussion or injection, Collection of reports of scientific and practical. Conference Modern Autoclaved Aerated Concrete,, Yekaterinburg, 2017, 4-8.

DOI: 10.31659/0585-430x-2018-757-3-62-64

[7] L.A. Suleymanova, I.A. Pogorelova, M.V. Marushko, Theoretical basis of formation highly organized porous structure of aerated concrete, Materials Science Forum. 945 (2019) 309-317.

DOI: 10.4028/www.scientific.net/msf.945.309

[8] M. Gomann, Porobeton. Manual, per. with him. under the editorship of A.S. Kolomatsky, LitKaraVan, Belgorod, (2010).

[9] C.B. Prokhorov, Specialized gas-forming agents of Gazobeto brands, Building materials. 8 (2015) 12-14.

[10] L.A. Suleymanova, Vibro-vacuum cellular concrete, dis. ... cand. tech. Sciences, Belgorod, (1997).

[11] S.A. Pogorelov, Influence of the rheological characteristics of mixtures on the preparation and properties of cellular concrete, Structures from composite materials. 3 (2003) 40-42.

[12] L.A. Suleymanova, K.A. Kara, K.A. Suleymanov, A.V. Pyrvu, D.D. Netsvet, N.P. Lukuttsova, The topology of the dispersed phase in gas concrete, Middle East Journal of Scientific Research. 18(10) (2013) 1492-1498.

[13] L.A. Suleymanova, V.S. Lesovik, K.R. Kondrashev, K.A. Suleymanov, N.P. Lukuttsova, Energy efficient technologies of production and use non-autoclaved aerated concrete, International Journal of Applied Engineering Research. 10 (5) (2015) 12399-12406.

[14] A.A. Rezanov, Technological principles for controlling macrostructural formation of gas silicate using an external gas phase pressure factor, Voronezh, (2011).

[15] D.A. Labuntsov, Mechanics of two-phase systems, MPEI, Moscow, (2000).

[16] S.S. Kutateladze, Heat and Mass Transfer and Waves in Gas-Liquid Systems, Nauka, Novosibirsk, (1984).

[17] M.A. Margulis, Sonoluminescence, Uspekhi Fizicheskikh Nauk. 170 (3) (2000) 263-287.

[18] A.V. Storcheus, On the Mechanism of Volcanic Explosions, Volcanology and Seismology. 4 (1983) 72–78.

[19] E.A. Smorodov, R.N. Galiakhmetov, Calculation of the installation for the accumulation of energy in gas bubbles, http://nuclearfusion.narod.ru/2rsmorod.htm.

[20] L.A. Suleymanova, Non-autoclaved aerated concrete on composite binders, dis. ... Dr. tech. Sciences, Belgorod, (2013).

[21] V.A. Lotov, Technology of materials based on silicate disperse systems, TPU, Tomsk, (2006).

[22] N.A. Mitina, Production of durable non-autoclaved aerated concrete by controlling the composition and properties of the initial mixtures, Tomsk State University, Tomsk, (2003).

[23] C. Krämer, M. Schauerte, T. Müller, S. Gebhard, R. Trettin, Application of reinforced three-phase-foams in UHPC foam concrete, Construction and building materials. 131 (2017) 746-757.

DOI: 10.1016/j.conbuildmat.2016.11.027

[24] CH 277-80, Instruction for the manufacture of cellular concrete products, Stroyizdat, Moscow, (1981).