3D Numerical and Experimental Investigation on Semi-Solid AlSi9Mg Alloy Slurry Prepared by Electromagnetic Stirring

Abstract:

To prepare semi-solid AlSi9Mg alloy slurry, we simulated electromagnetic stirring (EMS) based on a coupled 3D model of electromagnetic field, temperature field, and flow field by sequentially coupling ANSOFT and FLUENT software. Results show that magnetic flux density and electromagnetic body force (EMF) decrease and exhibit non-uniform patterns as stirring frequency increases. However, magnetic flux density and EMF increase in proportion to the stirring current but become more inhomogeneous. As EMF increases, the flow velocity and the depth of vortex in the semi-solid slurry gradually increase; thus, slurry temperature decreases. The deviation in temperature is then reduced between the center and the edge. As a result, the microstructure of the slurry evolves from coarse rosette grains to fine and spheroidal ones. By comparison, turbulent flow is generated by excessive and more unevenly distributed EMF, which causes deterioration in microstructures, such as the formation of cavities in the semi-solid AlSi9Mg alloy slurry. Based on simulation and experimental results, our conclusion is that reasonable process parameters have been obtained and verified experimentally. These results also show the validity and reliability of EMS-prepared semi-solid AlSi9Mg alloy.

• Periodical: Solid State Phenomena (Volumes 217-218)
• Pages: 208-218
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.217-218.208
• Online since: September 2014
• Authors: Chen Yang Zhang, Sheng Dun Zhao*, Guan Hai Yan, Yong Fei Wang
• Keywords: AlSi9Mg Aluminum Alloys, Electromagnetic Stirring, Microstructure, Numerical Simulation, Semi-Solid

References

[1] M.C. Flemings, Behavior of metal alloys in the semisolid state, Metall. Trans. B. 22B (1991) 269-93.

[2] Z. Fan, Semisolid metal processing, Int. Mater. Rev. 47 (2002) 49-85.

[3] H.V. Atkinson, Semisolid processing of metallic materials, Mater. Sci. Technol. 26 (2010) 1401-13.

[4] F. Czerwinski, On the generation of thixotropic structures during melting of Mg-9%Al-1%Zn alloy, Acta Mater. 50 (2002) 3265-81.

DOI: 10.1016/s1359-6454(02)00148-9

[5] D.H. Kirkwood, Semisolid metal processing, Int. Mater. Rev. 39 (1994) 173-89.

[6] E. Tzimas, A. Zavaliangos, A comparative characterization of near-equiaxed microstructures as produced by spray casting, magnetohydrodynamic casting and the stress induced, melt activated process, Mater. Sci. Eng. A. 289 (2000) 217-27.

DOI: 10.1016/s0921-5093(00)00907-2

[7] S. Chayong, H.V. Atkinson, P. Kapranos, Thixoforming 7075 aluminium alloys, Mater. Sci. Eng. A. 390 (2005) 3-12.

DOI: 10.1016/j.msea.2004.05.004

[8] H.V. Atkinson, Current Status of Semi-Solid Processing of Metallic Materials, Advances in Material Forming, Springer-Verlag, Paris, France , 2007, pp.81-98.

DOI: 10.1007/978-2-287-72143-4_6

[9] L.B. Trindade, A.C.F. Vilela, A.F.F. Filho, M.T.M.B. Vilhena, R.B. Soares, Numerical model of electromagnetic stirring for continuous casting billets, IEEE Trans. Magn. 38 (2002), p.3658–3660.

DOI: 10.1109/tmag.2002.804804

[10] S. Nafisi, D. Emadi, M.T. Shehata, R. Ghomashchi, Effects of electromagnetic stirring and superheat on the microstructural characteristics of Al-Si-Fe alloy, Mater. Sci. Eng., A. 432 (2006) 71-83.

DOI: 10.1016/j.msea.2006.05.076

[11] C.G. Kang, B.W. Bae, B.M. Kim, The grain size control of A356 aluminum alloy by horizontal electromagnetic stirring for rheology forging, J. Mater. Process. Technol. 187 (2007) 344–348.

DOI: 10.1016/j.jmatprotec.2006.11.181

[12] C.G. Kang, S.M. Lee, Development of a new rheology forming process with a vertical-type sleeve with electromagnetic stirring, Int. J. Adv. Manuf. Technol. 39 (2008) 462-473.

DOI: 10.1007/s00170-007-1242-2

[13] C. Mapelli, A. Gruttadauria, M. Peroni, Application of electromagnetic stirring for the homogenization of aluminum billet casting semi-continuous machine, J. Mater. Process. Technol. 210 (2010) 306-314.

DOI: 10.1016/j.jmatprotec.2009.09.016

[14] Z.F. Zhang, J.M. Kim, C.P. Hong, Numerical simulation of grain structure evolution in solidification of an Al-5. 0wt%Cu alloy under electromagnetic stirring and its experimental verification, ISIJ Int. 45 (2005) 183-191.

DOI: 10.2355/isijinternational.45.183

[15] X.R. Chen, Z.F. Zhang, J. Xu, Numerical simulation of electromagnetic field, flow field and temperature field in semi-solid slurry preparation by EMS, T. Nonferr. Metal. Soc. 20 (2010) 937-945.

DOI: 10.1007/s12598-010-0184-2

[16] Z.F. Zhang, X.R. Chen, J. Xu, Numerical simulation on electromagnetic field, flow field and temperature field in semisolid slurry preparation by A-EMS, Rare Metals. 29 (2010) 635-641.

DOI: 10.1007/s12598-010-0184-2

[17] V.L. Dao, S.D. Zhao, W.J. Lin, Numerical and experimental study on effect of process parameters on preparation of A356 aluminum alloy semi-solid slurry by electromagnetic stirring, Int. J. Appl. Electrom. 2(2013) 153-165.

DOI: 10.3233/jae-2012-1600

[18] H.V. Atkinson, Modelling the semisolid processing of metallic alloys, Prog. Mater. Sci. 50 (2005) 341-412.

[19] L. Orgeas, J.P. Gabathuler, Modelling of semi-solid processing using a modified temperature-dependent power-law model, Model. Simul. Mater. Sci. 11 (2003) 553-574.

DOI: 10.1088/0965-0393/11/4/309

[20] C.G. Kang, S.M. Lee, The effect of solid fraction and indirect forging pressure on mechanical properties of wrought aluminum alloy fabricated by electromagnetic stirring, Int. J. Adv. Manuf. Tech. 42 (2009) 73-82.

DOI: 10.1007/s00170-008-1575-5

[21] Il-Gab. Chung, Amir. Bolouri, Chung-gil. Kang, A study on semisolid processing of A356 aluminum alloy through vacuum-assisted electromagnetic stirring, Int. J. Adv. Manuf. Tech. 58 (2012) 237-245.

DOI: 10.1007/s00170-011-3376-5

[22] T.W. Kim, S.M. Lee, C.G. Kang, B.M. Kim, Rheological forging process of A6061 wrought aluminum alloy with controlled liquid fraction by electromagnetic stirring system, Int. J. Adv. Manuf. Tech. 40 (2009) 242-25.

DOI: 10.1007/s00170-007-1331-2