Structural Characterization of FeAl28Cr5 Alloy Deformed in the Hot Torsion Process

Abstract:

Current research in the field of iron aluminides are directed towards to understand the structural phenomena occurring during plastic deformation of these alloys. The obtained results of the study and collected informations will be used to determine the description of the structural changes taking place during hot deformation of Fe ̶Al alloys. The article presents the results of the study of the alloy FeAl28Cr5 deformed by hot torsion in temperature range of 800÷1100^°C and a strain rate of 0.1 s^-1. The analysis of the structure of the alloy FeAl28Cr5 allowed to reveal changes caused by dynamic processes of deformation. The results of torsion tests show the possibility to obtain a fine-grained structure with of parameters of the processes (T=1000^°C, 1100^°C) and strain of ε=40. After deformation at strain of (ε=40) the structure consists of fine grains with a misorientation angle higher than 15^°, and the average grain size diameter D=28.5 micrometers. Deformation at a temperature of T=1000^°C and 1100^°C is accompanied by superplastic flow effect.

• Periodical: Solid State Phenomena (Volume 246)
• Pages: 43-46
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.246.43
• Online since: February 2016
• Authors: Iwona Bednarczyk*, Magdalena Jabłońska
• Keywords: Alloys from Fe-Al System, EBSD Method, Flow Stress, Substructure, Torsion Plastometer

References

[1] D.G. Morris, S. Gunther, The influence of order on the recovery and recrystallizationof a Fe3Al alloy, Intermetallics 3 (1995) 483-491.

DOI: 10.1016/0966-9795(95)00007-l

[2] R. Balasubramaniam, On the role of chromium in minimizing room temperature hydrogen embrittlement in iron aluminides, Scripta Mater. 34 (1999) 127-133.

DOI: 10.1016/1359-6462(95)00495-5

[3] M. Zachman, W. Przetakiewicz: The possibility of forming an alloy superplastic based on intermetallic phase Fe3Al, Mater. Eng. 3 (2006) 312-314.

[4] Li D., Lin D., Liu Yi, Effect of temperature on the tensile properties and dislocationstructures of FeAl alloys, Mater. Sci. Eng. A249 (1998) 206-216.

[5] I. Bednarczyk, M. Jabłońska, Plasticity of low aluminium alloys from Fe-Al system, Arch. Metall. Mater. 57 (2012) 271-276.

[6] J. Cebulski, A. Fornalczyk, D. Pasek, Comparison of High Temperature Corrosion Resistance in Gaseous Environment of Alloys Based on Intermetallic Phase Matrix Fe40Al5CrZrB and Steel X12CrC, Arch. Metall. Mater. 59 (2014) 447-450.

DOI: 10.2478/amm-2014-0074

[7] M. Jabłońska, I. Bednarczyk, K. Rodak, A. Śmiglewicz, Study of the structure of intermetallics from Fe-Al system after the hot rolling, Metalurgija 55 1 (2016) 131– 134.

[8] A. Śmiglewicz, M. Jabłońska, Thermal expansion of the alloys from Al-Fe system, DSL 2011, Defect Diffus. Forum 326-328 (2012) 587-592.

DOI: 10.4028/www.scientific.net/ddf.326-328.587

[9] D. Kuc, G. Niewielski, M. Jabłońska, I. Bednarczyk, Deformability recrystallization of Fe-Al intermetallic phase – base alloy, JAMME 20 (2007) 143-146.

[10] D. Kuc, G. Niewielski, I. Bednarczyk, Structure and plasticity in hot deformed FeAl intermetallic phase base alloy, Mater. Charact. 60 (2009) 1185-1189.

DOI: 10.1016/j.matchar.2009.03.020

[11] M. Jabłońska, D. Kuc., I. Bednarczyk, Influence of deformation parameters on the structure in selected intermetallic from Al-Fe diagram, Solid State Phenom. 212 (2014) 63-66.

DOI: 10.4028/www.scientific.net/ssp.212.63

[12] I. Bednarczyk, D. Kuc, G. Niewielski, Influence of cumulative plastic deformation on microstructure of the FeAl intermetallic phase base alloy, Arch. Metall. Mater. 59 (2014) 987-991.

DOI: 10.2478/amm-2014-0191

[13] J.P. Chu, I.M. Liu, and others, Superplastic deformation in coarse-grained Fe-27Al alloys, Mater. Sci. Eng. A258 (1998) 236-242.

[14] M. Jabłońska, I. Bednarczyk, K. Rodak, A. Śmiglewicz, Study of the structure of intermetallics from Fe-Al system after the hot rolling, Metalurgija 55 (2016) 1, 67-71.

[15] P. Kratochvil, I. Schindler, Hot rolling of iron aluminide Fe28. 4Al4. 1Cr0. 02Ce (at %), Intermetallics 15 (2007) 436-438.

DOI: 10.1016/j.intermet.2006.06.005

[16] R. Łyszkowski, J. Bystrzycki, Hot deformation and processing maps of Fe3Al intermetallic alloy, Intermetallics 14 (2006) 1231-1236.

DOI: 10.1016/j.intermet.2005.12.014

[17] J. Konrad, S. Zaefferer, A. Schneider, D. Raabe, G. Frommeyer, Hot deformation behavior of a Fe3Al - binary alloy in the A2 and B2 - order regimes, Intermetallics 13 (2005) 1304-1312.

DOI: 10.1016/j.intermet.2004.10.017