The Influence of the Hardening Curve Profile on the Drawing Force of a Bar

Abstract:

The effect of the hardening curve profile of a workpiece material on the drawing force of the bar under the conditions of planar deformation is studied. Dependencies for determining the stress in the crimping part of the dies were obtained taking into account the profile and parameters of the hardening curve. A comparison of these dependencies with known formulas for the calculation of drawing stresses is provided. It is shown that for the exponent of the hardening curve n ≤1 and taking into account contact friction, the use of the arithmetic mean yield point value leads to a decrease in the calculated drawing stress value. The difference in the results of the calculation increases with a decrease in the exponent n and an increase in the friction coefficient, reaching 20% ​​or more at n≤0.35.

• Periodical: Solid State Phenomena (Volume 284)
• Pages: 690-695
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.284.690
• Online since: October 2018
• Authors: Georgy L. Baranov*
• Keywords: Bar Drawing, Drawing Stress, Strain Hardening

References

[1] I.L. Perlin, M.Z. Ermanok, Teoriya volocheniya, Metallurgiya, Moscow, (1971).

[2] O. Goffman, G. Zaks, Vvedenie v teoriyu plastichnosti dlya inzhenerov, Mashgiz, Moscow, (1957).

[3] S.I. Gubkin, Plasticheskaya deformatsiya metallov, Teoriya plasticheskoy obrabotki metallov, Metallurgizdat, Moscow, (1961).

[4] N.I. Sheftel, Proizvodstvo stalnyih kalibrovannyih prutkov, Metallurgiya, Moscow, (1970).

[5] N.N. Malinin, Tehnologicheskie zadachi plastichnosti i polzuchesti, Vyisshaya shkola, Moscow, (1979).

[6] E.P. Unksov, U. Dzhonson, V.L. Kolmogorov, Teoriya plasticheskih deformatsiy metallov, Mashinostroenie, (1983).

[7] A.I. Tselikov, A.D. Tomlenov, V.I. Zyuzin, Teoriya prokatki, Metallurgiya, Moscow, (1982).

[8] V.A. Kroha, Uprochnenie metallov pri holodnoy plasticheskoy deformatsii: Spravochnik, Mashinostroenie, Moscow, (1980).

[9] G.L. Baranov, Analiz napryazhennogo sostoyaniya pri volochenii polosyi, Izv. vuzov. Mashinostroenie, Moscow, 8 (1984) 113-117.

[10] G.L. Baranov, Kontaktnyie napryazheniya pri plasticheskom techenii metalla v klinovidnom kanale, Izv. vuzov. Chernaya metallurgiya, Moscow, 6(58) (2015) 429-433.

[11] A.L. Vorontsov, Yu.H. Hatsiev, Analiz zadach ob osadke, volochenii i pressovanii polosyi. Spravochnik, Inzhenernyiy zhurnal s prilozheniem, Moscow, 59 (2014) 10-16.

DOI: 10.14489/hb.supp.2014.09.pp.010-016

[12] S.B. Maksimov, Techenie materiala v shodyaschihsya kanalah pri vyipolnenii na kontakte zakona treniya Kulona, Izv. vuzov. Chernaya metallurgiya. Moscow, 1 (1990) 43-45.

[13] A.N. Levanov, V.L. Kolmogorov, S.P. Burkin, Kontaktnoe trenie v protsessah obrabotki metallov davleniem, Metallurgiya, Moscow, (1976).

[14] A.P. Grudev, Yu.V. Zilberg, V.T. Tilik, Trenie i smazki pri obrabotke metallov davleniem, Metallurgiya, Moscow, (1982).

[15] E.I. Isachenkov, Kontaktnoe trenie i smazki pri obrabotke metallov davleniem, Mashinostroenie, Moscow, (1978).

[16] V.S. Smirnov, Teoriya obrabotki metallov davleniem, Metallurgiya, Moscow, (1973).

[17] G.L. Baranov, Influence of Contact Friction on the Stress State of Strip in Drawing, Steel in translation, 6(44) (2014) 460-465.

DOI: 10.3103/s0967091214060035

[18] G.L. Baranov, Stress state of the metal when drawing continuous axisymmetric profiles in conical matrices, Steel in translation, 1(44) (2014) 65-70.

DOI: 10.3103/s0967091214010033

[19] G.E. Arkulis, V.G. Dorogobid, Teoriya plastichnosti. Uchebnoe posobie dlya vuzov, Metallurgiya, Moscow, (1987).

[20] G.N. Guryanov, Vliyanie uprochneniya metalla na raschetnyie znacheniya napryazheniya volocheniya, Zavodskaya laboratoriya. Diagnostika materialov, 5(77) (2011) 59-62.