Young Modulus at High Temperatures

Abstract:

The dependence of the young modulus of metals and alloys on the high temperature must be taken into account in metallurgy in the hot rolling of steel sheet on sheet-rolling mills, hot flattening of steel sheet in the sheet straightening machines, press forming forgings from hot steel sheet, hot volume stamping of metal products, and so on. For example, on the mill 5000 by SMS Siemag, the sheet-rolling of steel strips from the hot slabs at the stand Quarto (the maximum force of 120 MN) occurs at a temperature from 750 °С to 1050 °С, but the pre-flattening of hot steel strip on the five-roller sheet-straightening machine by SMS Siemag occurs usually in the temperature range from 600 °С to 760 °С. In this paper, based on the analysis of experimental data about the dependence of the young modulus for various steel alloys, the analytical dependence of the young modulus on temperature is obtained.

• Periodical: Solid State Phenomena (Volume 299)
• Pages: 535-540
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.299.535
• Online since: January 2020
• Authors: Vladimir N. Shinkin
• Keywords: Steel Alloys, Temperature Dependence, Young Modulus

References

[1] D. Banabic, Multiscale Modeling in Sheet Metal Forming, Springer, (2016).

[2] D. Banabic, Sheet Metal Forming Processes: Constitutive Modelling and Numerical Simulation, Springer, (2010).

[3] V.N. Mozgunov, M.V. Serov, A.A. Zubarev, Stability of a three-layer shell made of composite material with a net-like filler, Khimicheskoe i Neftegazovoe Mashinostroenie 10 (1994) 15-17.

DOI: 10.1007/bf01150252

[4] V.N. Mozgunov, M.V. Serov, A.A. Zubarev, Stability of a three-layer shell made of a composite material with a reticular filler, Chemical and Petroleum Engineering 30(10) (1994) 480-485.

DOI: 10.1007/bf01150252

[5] J. Chakrabarty, Theory of Plasticity, Butterworth-Heinemann, (2006).

[6] J. Chakrabarty, Applied Plasticity, Springer, (2010).

[7] V.N. Shinkin, Calculation of steel sheet's curvature for its flattening in the eight-roller straightening machine, Chernye Metally 2 (2017) 46-50.

[8] V.N. Shinkin, Calculation of bending moments of steel sheet and support reactions under flattening on the eight-roller straightening machine, Chernye Metally 4 (2017) 49-53.

[9] V.N. Shinkin, Asymmetric three-roller sheet-bending systems in steel-pipe production, Steel in Translation 47(4) (2017) 235-240.

DOI: 10.3103/s0967091217040106

[10] F. Klocke, Manufacturing Processes: 1. Cutting, Springer, (2011).

[11] F. Klocke, Manufacturing Processes: 4. Forming, Springer, (2013).

[12] V.N. Mozgunov, M.V. Serov, A.A. Zubarev, Research of stability of the three-layer cylindrical shells with netted filler, Khimicheskoe i Neftegazovoe Mashinostroenie 3 (1997) 23-26.

DOI: 10.1007/bf02418472

[13] V.N. Mozgunov, M.V. Serov, A.A. Zubarev, Stability investigations of three-layer cylindrical shells with a grid filler, Chemical and Petroleum Engineering 33(3) (1997) 272-277.

DOI: 10.1007/bf02418472

[14] J. Lin, D. Balint, M. Pietrzyk, Microstructure Evolution in Metal Forming Processes, Woodhead Publishing, (2012).

[15] C.V. Nielsen, W. Zhang, L.M. Alves, N. Bay, P. Martins, Modeling of Thermo-Electro-Mechanical Processes: Applications in Metal Forming and Resistance Welding, Springer, (2013).

DOI: 10.1007/978-1-4471-4643-8

[16] V.N. Shinkin, Failure of large-diameter steel pipe with rolling scabs, Steel in Translation 47(6) (2017) 363-368.

DOI: 10.3103/s0967091217060109

[17] V.N. Shinkin, Simplified calculation of the bending torques of steel sheet and the roller reaction in a straightening machine, Steel in Translation 47(10) (2017) 639-644.

DOI: 10.3103/s0967091217100072

[18] V.N. Shinkin, Calculation of technological parameters of O-forming press for manufacture of large-diameter steel pipes, CIS Iron and Steel Review 13 (2017) 33-37.

DOI: 10.17580/cisisr.2017.01.07

[19] M. Predeleanu, P. Gilormini, Advanced Methods in Materials Processing Defects, vol. 45, Elsevier Science, (1997).

[20] D. Rees, Basic Engineering Plasticity: An Introduction with Engineering and Manufacturing Applications, Butterworth-Heinemann, (2006).

[21] A.S. Zubchenko, Reference-Book of Steels and Alloys, Mechanical Engineering, (2001).

[22] B.M. Drapkin, V.K. Kononenko, V.F. Bezyazichniy, Properties of Alloys at Extreme Condition, Mechanical Engineering, (2004).

[23] Y. Lim, R. Venugopal, A.G. Ulsoy, Process Control for Sheet-Metal Stamping Process Modeling, Controller Design and Stop-Floor Implementation, Springer, (2014).

DOI: 10.1007/978-1-4471-6284-1

[24] R.S. Hingole, Advances in Metal Forming: Expert System for Metal Forming, Springer, (2015).

DOI: 10.1007/978-3-662-44497-9

[25] V.N. Shinkin, Mathematical model of technological parameters' calculation of flanging press and the formation criterion of corrugation defect of steel sheet's edge, CIS Iron and Steel Review 13 (2017) 44-47.

DOI: 10.17580/cisisr.2017.01.10

[26] V.N. Shinkin, Springback coefficient of the main pipelines' steel large-diameter pipes under elastoplastic bending, CIS Iron and Steel Review 14 (2017) 28-33.

DOI: 10.17580/cisisr.2017.02.06

[27] V.N. Shinkin, Arithmetical method of calculation of power parameters of 2N-roller straightening machine under flattening of steel sheet, CIS Iron and Steel Review 14 (2017) 22-27.

DOI: 10.17580/cisisr.2017.02.05

[28] C.R. Calladine, Plasticity for Engineers: Theory and Applications, Woodhead Publishing, (2000).

[29] Y. Qin, Micromanufacturing Engineering and Technology, William Andrew, (2015).

[30] C.E. Wilko, Formability: A Review of Parameters and Processes that Control, Limit or Enhance the Formability of Sheet Metal, Springer, (2011).