Paper Titles

Process Development for Solid Fuel Use at Siderite Ore Roasting in Shaft Furnace
p.606

The Phase Composition of Products from Electro-Erosive Cobalto-Chrome Powders, Obtained by Additive Technologies
p.611

Theoretical Justification of the Longitudinal Rolling Method of the Thick Sheets by the Severe Shear Deformation
p.617

Features of the Use of Equilibrium State Diagrams for Description of Crystal Growth from Metastable Melts
p.622

Identification for Technological Capabilities of Titanium and Aluminum Alloys in Deep Drawing Process
p.628

The Research of the Possibilities of Using Purge Methods for the Manufacture of Casting Cores from Mixtures Based on Secondary Polymers and Technical Lignosulphonates
p.634

The Role of the Primary Structure in the Formation of the Mechanical Properties of Steel Castings
p.641

Investigation of Ti-6Al-4V Alloy In Situ Manufactured Using Selective Laser Melting from Elemental Powder Mixture
p.646

Increasing Wear Resistance of Chizel Tools Working Bodies Based on Improving the Metallographic Structure of Grey Cast Iron
p.652

HomeSolid State PhenomenaSolid State Phenomena Vol. 299Identification for Technological Capabilities of...

Identification for Technological Capabilities of Titanium and Aluminum Alloys in Deep Drawing Process

Article Preview

Abstract:

The paper describes a method which has been developed for obtaining the limiting drawing ratio of titanium and aluminum alloys, and determines the moment of failure of the work-piece. This method is based not only on the use of Forming Limit Diagram (FLD) in predicting the failure of the blank, but also the using method of variable parameters of elasticity in determining the stress-strain state in deep drawing process.

You might also be interested in these eBooks

Materials Engineering and Technologies for Production and Processing V

Info:

Periodical:

Solid State Phenomena (Volume 299)

Pages:

628-633

DOI:

https://doi.org/10.4028/www.scientific.net/SSP.299.628

Citation:

Cite this paper

Online since:

January 2020

Authors:

S.I. Feoktistov*, Kyaw Zayar Soe

Keywords:

Deep Drawing, FLD-Diagram, Forming Limit Diagram, Method of Variable Parameters of Elasticity, Technological Capabilities

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2020 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

[1] V.P. Romanovsky, Handbook of cold stamping: fifth ed,. M., Mechanical engineering, 1977 p.423.

[2] Dorel Banabic. Sheet Metal Forming Processes. Constitutive Modelling and Numerical Simulation. London-New York: Springer Heidelberg Dordrecht, 2010, p.301.

[3] G.S. Ma, M. Wan, X.D. Wu, Theoretical prediction of FLDs for Al-Li alloy at elevated temperature based on M-K model, J. Chinese Journal of Nonferrous Metals. 18 (2008) 980-984.

[4] M. Yang, X.H. Dong, The Forming Limit Prediction Using a Rate-Dependent Crystal Plasticity Model, J. Journal of ShangHai JiaoTong University. 42 (2008) 720-723.

[5] P.M. Du, L.H. Lang, B.S. Liu, Theoretical prediction and parameter influence of FLDs based on M-K model, J. Journal of Plasticity Engineering. 18 (2011) 84-89.

[6] G.N. Chen, S.G. Hu, Damage, Instability and Construction of Forming Limit Curve in Sheet Metal Stretch Forming , J. Journal of Plasticity Engineering. 1 (1994) 31-46.

[7] A. Kami, B.M. Dariani, Numerical determination of the forming limit curves of anisotropic sheet metals using GTN damage model, J. Journal of Materials Processing Technology. 216 (2015) 472-483.

DOI: 10.1016/j.jmatprotec.2014.10.017

[8] A. K Ghosh, The influence of strain hardening and strain-rate sensitivity on sheet metal forming [J]. Journal of Engineering Materials and Technology, 99(3) (1977) 264−274.

DOI: 10.1115/1.3443530

[9] K. Nakazima, T.Kikuma, Forming Limits under biaxial stretching of sheet metals, Testu-to Hagane, 53 (1967) 455-458.

[10] Z. Marciniak, K. Kucznski, Limit strain in the process of stretch forming sheet metal, International Journal of Mechanical science. 9 (1967) 609-620.

DOI: 10.1016/0020-7403(67)90066-5

[11] A.S. Chumadin, Theory and calculations of sheet-stamping processes (for engineers), second ed, M Exservice VIP, 2014, p.216.

[12] N.N. Malinin, Applied theory of plasticity and creep. Textbook for university students. second ed, Mechanical Engineering,, Moscow, 1975, p.400.

[13] M.V. Storozhev, E.A. Popov, Theory of metal working with pressure, textbook for high schools, forth ed, M., Mechanical Engineering, (1977).

[14] I.A. Birger, Round plates and shells of rotation, Oborongiz, 1961, p.368.

[15] S.I. Feoktistov, Automation of the design of technological processes and accessories of the blank-forming production of the aviation industry, Vladivostok, 2001, p.183.

[16] M. N. Gorbunov, Technology of procurement and stamping works in the production of aircraft, Mechanical Engineering, Moscow, 1981, p.224.

[17] E.A. Popov, Fundamentals of sheet punching theory, second ed., Mechanical Engineering, Moscow, 1977, p.278.

[18] J. H. Hollomon, Tensile deformation,, Transaction of American Institute of Mechanical Engineering, (1945) vol. 162, p.268–277.

[19] I. F. Obraztsov, F. I. Samples, A. A. Bulychev and V. V.Vasiliev, Structural mechanics of aircraft, Mechanical engineering, Moscow, (1986) p.536.