Study of Impact Velocity on Residual Stress and Surface Hardness of SKD11 in Shot Peening Process

Abstract:

Shot peening process could create compressive residual stress and increase surface hardness and hence also used to improve material surface properties in case thermal effect is to be avoided. The shot peening process parameters such as pressure which result in different shot impact velocity could affect the compressive residual stress distribution which results in different post-process material properties. The ability to understand and predict the effect of process parameters on stress distribution could be very useful to control and obtain material properties as required. In this work, a shot peening process commercially available locally was investigated. The residual stress distribution after shot peening of SKD11 was studied using the finite element (FE) technique. A single shot impact was simulated. A maximum velocity with a miximum impact angle was assumed. The computational predictions showed higher compressive residual stress developed with increasing shot velocity as expected due to higher impact energy. However, experimental results suggested that the process arrangement and machine control highly affect the properties of the material after process. The compressive residual stress and surface hardness obtained experimentally was almost unchanged with an increase in pressure from 0.35MPa to 0.6MPa. It was found that, due to machine arrangement, an increase in impact velocity at higher pressure was relatively small and did not observed in all effected area due to fixed arrangement of nozzle and samples. Hence, research results suggested that a detail computational methodology including the effect of unevent impact velocity and impact angle should be employed to increase the predictive ability of the FE model. The current work could be extended to include such effects with no major difficulty to develop useful information for the design of shot peening process for any specific machine and arrangement.

• Periodical: Solid State Phenomena (Volume 304)
• Pages: 127-134
• DOI: https://doi.org/10.4028/www.scientific.net/SSP.304.127
• Online since: May 2020
• Authors: Pudsadee Chupong*, Karuna Tuchinda
• Keywords: Finite Element Method, Hardness, Residual Stress, Shot Peening Process, SKD11

References

[1] K.G. Budinski and M.K. Budinski, Tool steels, Engineering Materials Properties, and Selection 8th edit, Upper Saddle River, NJ: Prentice Hall, (2005) 459-501.

[2] A. Ghiotti, S. Bruschi, Tribological Behavior of DLC Coatings for Sheet Metal Forming Tools, Wear, 271 (2011) 2458-2454.

DOI: 10.1016/j.wear.2010.12.043

[3] M. Vilaseca, J.Pujante, G.Ramírez, D.Casellas, Investigation into Adhesive Wear of PVD Coated and Uncoated Hot Stamping Production Tools, Wear, 308 (2013) 459-501.

DOI: 10.1016/j.wear.2013.07.003

[4] D. Ko, D. Kim, B. Kim, Finite element analysis for the wear of Ti–N coated punch in the piercing process, Wear, 252 (2002) 859–869.

DOI: 10.1016/s0043-1648(02)00032-7

[5] Th. Chaisea, J. Li, D. Nélias, R. Kubler, S. Taheri, G. Douchet, V. Robin and Ph. Gilles, Modelling of multiple impacts for the prediction of distortions and residual stresses induced by ultrasonic shot peening (USP), Journal of Materials Processing Technology, 212 (2012) 2080– (2090).

DOI: 10.1016/j.jmatprotec.2012.05.005

[6] Y. Kameyama, K. Nishimura, H. Sato and Ry. Shimpo, Effect of fine particle peening using carbon-black/steel hybridized particles on tribological properties of stainless steel, Tribology International, 78 (2014) 115–124.

DOI: 10.1016/j.triboint.2014.05.006

[7] T. Morita, Sh. Noda, Ch. Kagaya, Influence of hardness of substrates on properties of surface layer formed by fine particle bombarding, Materials Science & Engineering A, 574 (2013) 197–204.

DOI: 10.1016/j.msea.2013.03.026

[8] T. Morita, H. Nakaguchi, Sy. Noda and Ch. Kagaya, Effects of Fine Particle Bombarding on Surface Characteristics and Fatigue Strength of Commercial Pure Titanium, Materials Transactions, 53 (2012) 1938–(1945).

DOI: 10.2320/matertrans.m2012226

[9] Y. Kameyama, J. Komotori, Tribological properties of structural steel modified by fine particle bombardment (FPB) and diamond-like carbon hybrid surface treatment, Wear, 263 (2007) 1354–1363.

DOI: 10.1016/j.wear.2007.01.075

[10] O. Higounenc, Correlation of shot peening parameters to surface characteristic, Shot peening, 28-35.

[11] D. Kirk, Work-Hardening During Peening, The Shot Peener (2017), pp.26-34.

[12] F.P. Renaud, Optimization of the Shot Peening Parameters, Shot peening, 119-128.

DOI: 10.1002/3527606580.ch17

[13] M. Widmark, A. Melander, Effect of material, heat treatment, grinding and shot peening on contact fatigue life of carburized steels, International Journal of Fatigue, 21 (1999) 309-327.

DOI: 10.1016/s0142-1123(98)00077-2

[14] A. M. Korsunsky, An analysis of residual stresses and strains in shot peening, ICRS-5 Proceedings, (1999).

[15] H. Aoki, E. Nagashima, T. Miura, Effect of shot peening conditions on fatigue strength of carburized steels, ICSP-4 Proceedings, 513-518.

[16] S.A. Meguid, G. Shagal, J.C. Stranart, J. Daly, Three-dimensional dynamic finite element analysis of shot peening induced residual stresses, Finite Elements in Analysis and Design,31 (1999) 179–191.

DOI: 10.1016/s0168-874x(98)00057-2

[17] S.A. Meguid, G. Shagal, J.C. Stranart, Finite element modeling of shot peening residual stresses, Journal of Materials Processing Technology, 92–93 (1999) 401–404.

DOI: 10.1016/s0924-0136(99)00153-3

[18] S.A. Meguid, G. Shagal, J.C. Stranart, 3D FE analysis of peening of strain-rate sensitive materials using multiple impingement model, International Journal of Impact Engineering, 27 (2002) 119–134.

DOI: 10.1016/s0734-743x(01)00043-4

[19] G.H. Majzoobi, R. Azizi, A 3-d numerical study of shot peening process using multiple shot impacts, 9th International Conference on Shot Peening (ICSP), France, Paris, (2005).

DOI: 10.1016/j.jmatprotec.2005.02.139

[20] K. Tuchinda, E. Juntasaro, O. Deawwanich and P. Chupong, Development of On-Demand Material Properties by Spraying Process, TRF Final Report, Thailand Research Fund (TRF), (2017).

[21] S. Kang, I. Kang, K. Lee, D. Kwon, Method for correcting an incomplete shape of a spherical indenter through continuous effective radius, Korea, Patent no.WO201003293A3, (Jun 2010).