Search results

Experimental Procedure Fig. 1 Density change in the sintered samples with initial preservation ratios (RA) at the first mixing step.
Results and Discussion The measured density of the sintered samples is shown in Fig. 1.
References [1] M.D.
Forum 475-479 (2005) 1165-1168
Kim, Microstructure and piezoelectric properties of lead-free (1-x)(Na0.5K0.5)NbO3-xCaTiO3 ceramics, J.

Annual emissions of sewage sludge (moisture weight percentage) growth rate of greater than 10% [1], in the period of “12th Five -Year Plan", discharge amount of sewage sludge from Urban Wastewater Treatment Firm would mount up with an annual increase of 15%, the annual discharge amount would exceed 46 million tons.
When the problem what was shortage of heat source coming, opening reclaimed water heat pump for supplementary heating (see Fig.1). 1- drying chamber 2- solar collector 3,5,23, 25,26- water pump 4- water tank 6-endothermic section（winding heat exchanger tube） 8- Expansion Valve 9,23- evaporator 7,13,17,18,20,22,24,26,30- solenoid valve 10- gas-liquid separator 11- compressor 12- heat liberation section（blower） 14- Water-cooling condenser 15- air-cooled condenser 16- Ventilation systems 19-reclaimed water tank 21- plate-frame heat exchangers 29- throttle device 31- water tank 32- waste gas treatment Fig.1.
Drying process of the system was such as graph 1, open water pumps 3, the low temperature water relatively in the storage tank water flowed in flat collector, then absorption of heat, returned tank after heating up.
References [1] Yuan Liugen.
Acta Energiae Solaris Sinica, 2005, 25(4): 479－482.

The SEM micrograph of microstructure for as-cast and HIP treated NiAl-28Cr-5.5Mo-0.5Hf-0.02P alloy is shown in Fig. 1.
The alloy as-cast was composed of three phases: (i) the lamellar Cr(Mo) phase, (ii) the NiAl matrix, and (iii) the discontinuously distributed white phase(Fig. 1(a)).
Conclusions (1) For primary creep of NiAl-28Cr-5.5Mo-0.5Hf-0.02wt%P alloy, the Li’s equation gives less satisfactory representation than that of Garofalo’s relation
References [1] Miracle D B: The physical and mechanical properties of NiAl.
MATERIALS SCIENCE FORUM, Vol.  475/479 (2005), pp. 771-774

Garcia3,f 1 Federal Institute of Education, Science and Technology – IFPA PO Box 479 - 66093-020 – Belém, PA, Brazil 2 Department of Mechanical Engineering, Fluminense Federal University Av. dos Trabalhadores 420 – 27255-125 - Volta Redonda, RJ, Brazil 3 Department of Materials Engineering,University of Campinas – UNICAMP PO Box 6122 - 13083–860 - Campinas, SP, Brazil a lgouvea@fem.unicamp.br, b paulo.andre@foa.org.br, c ileao@metal.eeimvr.uff.br, d dmoutinho@fem.unicamp.br, e otvrocha@oi.com.br, f amaurig@fem.unicamp.br Keywords: Solidification, Ternary alloys, Macrosegregation, Porosity.
Porosity has also a deleterious effect on the machinability and surface properties of aluminum castings [1-2].
The pseudo-binary phase diagrams as a function of Cu, Si and H concentrations obtained by this routine are presented in Fig. 1
( A ) ( B ) ( C ) Fig. 1.
References [1] J.P.

The mass ratio of corundum grinding balls and materials was 8:1.
Fig.1 XRD pattern of the as-prepared AlON powders Fig.2 SEM image of the ball milled AlON powders Results and Discussion Powder Properties.
The XRD pattern of the AlON powders prepared by carbothermal reduction and nitridation method is shown in Fig. 1.
References [1] C.T.
Ceram.Soc. 62(1979) 476–479

Mohanraj4,d 1 Department of Mechanical Engineering, Dr.
Table 1.
The pattern (shown in Fig.1) shows the presence of β Ti and α Ti peaks suggesting that the matrix contains both β and α phases in the composites.
References [1] B.V.
Materials science forum 2005:475-479;963-966 [4] Ravi Chandran KS, Panda KB.

Introduction As we all know, pollution on water resources is more and more serious with the development of industry [1].
The GO-PVA composites were heated at 750 °C for 2 h with a heating rate of 5 °C min-1 in a furnace with Ar.
Fig.1 gives the FESEM images of the GR aerogels.
References [1] R.
Technol. 43(2008) 473-479

Once the problem of membrane fouling is solved, it will encourage the wide application and commercialization of A/O-MBR drastically.[1] Extracellular polymeric substance (EPS) that is absorbed on membrane surface is considered to be a key factor for membrane fouling.[2] EPS is composed of protein and carbohydrate, and is generally classified into bound-EPS （B-EPS）and soluble-EPS（S-EPS）[3,4] in active sludge.
There are experimental operating parameters in Table 1 .
References [1] Ji L, Zhou J.
Journal of Membrane Science, 2006, 276(1): 168-177
Seoul, Korea. 2004: 479-486.

Fig.1 shows the principle of zinc-bromine battery.
Fig.1 the principle of zinc-bromine battery Fig.2 the smart-grid with chemical storage device Application Smart-grid is combined by the power electronic technology, information technology, distributed generation, and storage technology.
References [1] Skyllas-Kazacosm, Peng C, Cheng M.
Battery energy storage technologies [J]．Proceedings of the IEEE, 1993, 81(3): 475-479

Nie 1,a and Z.
The slope compatibility conditions can be expressed as: ∑=== N j jij k k i vA ldx dv 1 1 ϕ , Mk L,2,1=
Numerical Examples Example 1.
References [1] W.F.
Computers & Structures Vol. 48 (1993), p. 473-479