Search results

This study aimed to use the zinc-dust which is a waste from hot-dip galvanizing plant for the synthesis of ZnO nanoparticles using microwave-assisted process.
But in this work, we aim to use an industrial waste called Zn-dust, which was derived from hot-dip galvanizing plant in metal plating industry, as starting materials to synthesize ZnO by microwave-assisted process.
Popovi, Influence of synthesis route on the formation of ZnO particles and their morphologies, Journal of Alloys and Compounds, 429 (2007) 242–249
Li, Synthesis and surface modification of ZnO nanoparticles, Chemical Engineering Journal, 119 (2006) 71-81
Lu,Synthesis and characterization of nano-sized ZnO powders by direct precipitation method, Chemical Engineering Journal, 144 (2008) 509-513 [8] M.

The aim of this work is to investigate the effect of substitution of strontium ions with cerium ions in structural and magnetoelectric properties of W-type strontium hexaferrites, unlike other studies which have replaced the Sr2+ and Fe3+ by Ce3+ [3,5].
Rana, Role of Ce–Mn substitution on structural, electrical and magnetic properties of W-type strontium hexaferrites, Journal of Alloys and Compounds 509 (2011) 8042– 8046
Rana, Effect of Ce Substitution on Structural and Electrical Properties of W-type Strontium Hexaferrite Nanomaterials, Journal of the Chemical Society of Pakistan, 34 (2012) 579-583
Alloys & Compounds, 478 (2009) 847-852

The fungus Aureobasidium pullulans HN produced two major anti-biofouling bioactive compounds.
The compounds were recognized as palmitic and myristic acids.
Journal of Alloys and Compounds, 654 (2016) 561–566
Gao, Extraction and performance study of antifouling compounds produced by marine microorganism and microalgae [D].
Lu, Natural antifouling compounds produced by a novel fungus Aureobasidium pullulans HN Isolated from marine biofilm.

Anodization and heat treatment procedures have proved advantageous to titanium alloys in terms of producing oxide films that can offer these alloys an improved biological performance.
The aim of this study is to keep in focus the use of titanium alloy as an implant inside the bone tissue and hence the Hanks Balanced Salt Solution was used to simulate the extracellular interstitial environment.
The untreated alloys, however, exhibited a one-time constant response of a single oxide layer.
Al-Jabab, Saudi Dental Journal Vol. 14, No. 3 (2002),118-125 [4] M.
Saluja: Journal of Materials Engineering and Performance Vol. 17, No. 5 (2008), 695-701 [5] K.

Review: Effect of Alloying Element on Al-Si Alloys M.N.
In this paper, the authors aim to review the mechanical and physical influences of alloying elements brought to Al-Si alloys.
Adding Mg to Al-Si alloys was proven to increase the mechanical strength of the alloys with an expense of ductility.
It serves as an iron corrector by forming FeNiAl9 intermetallic compound.
Sokolowski, "Microstructure and mechanical properties of AC AlSi9CuX alloys," Journal of Achievements in Materials, vol. 24, no. 2, pp. 51-54, 2007

The media is commonly used with a fluid compound to create a wet mix.
Fluid compound was a non-foaming general purpose fluid.
Compound was added at regular intervals to maintain a constant wet mix.
[6] Fligge K.A., Chemical compounds—Critical to high-quality metal parts, Metal Finishing Volume 95, Issue 7, July 1997, P. 26
[9] Baghbanan M.R., Yabuki A., Timsit R.S., Spelt J.K., Tribological behavior of aluminum alloys in a vibratory finishing process, Jorunal of Wear 255 (2003), pp. 1369–1379

Introduction Many magnetic sintered alloys, like NdFeB [1], Sm(CoFeCuZr)z [2,3] and SmCo5 [4,5] need a post sintering heat treatment to develop higher coercivity.
The aim of this study is an evaluation of the kinetics of diffusion in typical magnets.
Alloys Compd.
Fruchart: Journal of Alloys and Compounds Vols. 356–357 (2003), p. 390
Alloys Compd.

In order to achieve the aim of this study, one way has been used, is strengthening the fuselage structure by the appropriate material and stacking sequence.
The methodology which has been followed to achieve the aim of the present study as follow.
Mahantayya KHiremath, "Crash Analysis of Unmanned Aerial Vehicle Using FEA " International Journal of Innovative Research in Science, Engineering and Technology, vol.
Liu, "A modified Johnson Cook model of dynamic tensile behaviors for 7075-T6 aluminum alloy," Journal of Alloys and Compounds, vol. 619, pp. 186-194, 2015
Rao, "Energy absorption characteristics of aluminium alloy AA7XXX and AA6061 tubes subjected to static and dynamic axial load," International Journal of Crashworthiness, vol. 19, pp. 139-152, 2014

On this basis, they have conducted research on new brush materials, the main purpose is through "save cost" alloy modification, raise (or not lower) original performance of AgPd alloys, reducing the use of Pd, so reduce the manufacturing cost of brush material.
(a) AgPd surface morphology of AgPd50/BZn composites (b) surface morphology of compound interface Figure 4.
Journal of Changchun University. 111 (2001) 11-14
The Chinese Journal of Nonferrous Metals. 15 (2005) 1766-1769
The Chinese Journal of Nonferrous Metals. 10 (2000) 97-101

The aim of this research is to investigates the structural, morphological and dielectric properties of TiO2-doped ZnAl2O4 nanocrystals thin films.
Shuai, Synthesis of (1−x)ZnAl2O4–xTiO2 microwave dielectric ceramics by molten-salt process, Journal of Alloys and Compounds 508, (2010) 507–511
Park, Crystal structure and microwave dielectric properties of (1―x) ZnTa2O6―xTiO2 ceramics, Journal of Alloys and Compounds 537, (2012) 221-226
Li, Characterization and dielectric behavior of a new dielectric ceramics Ca(Mg1/3Nb2/3)O3–(Ca0.8Sr0.2)TiO3 at microwave frequencies, Journal of Alloys and Compounds 484, (2009) 494-497
Shi, Facile synthesis of mesoporous ZnAl2O4 thin films through the evaporation-induced self-assembly method, Journal of Alloys and Compounds 488, (2009) 320-324