Search results

Material modeling.
The material of the inner steel liner with 25 mm thickness was assumed to be equivalent to the 4340 STEEL with the Johnson-Cook constitutive law [4].
Romero, Strain growth in spherical explosive chambers subjected to internal blast loading, International Journal of Impact Engineering, 28 (2003) 967-983
Hokamoto, Analysis of structural damage using simulation and experimental studies in the explosion pit at Kumamoto University, Science Technology of Energetic Materials, 76 (2016) 133-138
Cook, A constitutive model and data for materials subjected to large strains, high strain rates, and high temperatures, Proc. 7th Int.

No less promising thematic areas for "smart" materials are composite materials for aviation and space technology.
PN Lebedev Russian Academy of Sciences., Publisher: Physical Institute.
Characterization of thin carbon films capable of low-field electron emission //Journal of Vacuum Science & Technology B, Nanotechnology and Microelectronics: Materials, Processing, Measurement, and Phenomena. – 2018. – V. 36. – №. 2. – С. 02C108
Classification of high-damping metallic materials //Strength of Materials. – 1986. – V. 18. – №. 10. – p. 1325-1329
[17] Mechanical behavior of structural materials.

Extended shelf-life of materials can be achieved by reducing the moisture content to levels below those required by microorganisms [5].
Materials and Methods Materials Ganoderma lucidum after being harvested in Dong Nai Province, Vietnam had a moisture content of about 75% (wet basis) and were dried by hot air convective oven at 50°C for 3 - 4 days to reach moisture content of about 20% (wet basis).
The experimental materials were spread on a stainless steel mesh (20 x 20 cm) to form a thin layer.
Murata, Simultaneous heat and mass transfer between air and soybean seeds in a concurrent moving bed, International Journal of Food Science and Technology. 36 (2001) 393–399
Chirife, Prediction of effect of temperature on water sorption isotherms of food materials, Journal of Food Technology. 11 (1976) 109-116

Smart Materials and Structures, 14 (2004), 197-204
Journal of Applied Physics, 87 (2000), 21-31
Shahinpoor, "Potential applications of electroactive polymer sensors and actuators in MEMS technologies", SPIE Smart Materials & MEMS Publication No. 42 (2000)34-40
[15] Cheng et al "Development of IPMC actuator for flapping motion of dragonfly" Advanced Materials Research, 150 (2010), 1301-1304
[19] Palmre et al "An IPMC-enabled bio-inspired bending/twisting fin for underwater applications" Smart Materials and Structures, 22 (2011)

Udomsamuthirun2,b 1 Department of science and Mathematics, Faculty of Science and Technology, Pathumwan Institute of Technology, Bangkok 10330,Thailand. 2 Prasarnmit Physics Research Unit, Department of Physics, Faculty of Science, Srinakharinwirot University, Sukumvit 23, Bangkok 10110,Thailand.
Superconductivity is a phenomenon of exactly zero electrical resistance and expulsion of magnetic fields occurring in certain materials when cooled below a characteristic critical temperature.
Introduction The two-band non-magnetic superconductors can be found in borocarbides material.
Hampshire, The non-hexagonal flux-line lattice in superconductors, Journal of Physics: Condensed Matter. 13(2001) 6095-6113
Udomsamuthirun, London penetration depth λ(T) in Type 1.5 superconductor by Ginzburg-Landau approach, Advanced Materials Research. 770(2013) 291-294

The principle of the choice of materials depends on the task.
So, for example, compositions based on mineral raw materials are known.
Series: Earth and Environmental Science, 87.8 (2017) 082047
Gabarrell, Environmental assessment of façade-building systems and thermal insulation materials for different climatic conditions Journal of Cleaner Production, 113 (2015) 102-113
Zhang, Novel application of glass fibers recovered from waste printed circuit boards as sound and thermal insulation material Journal of materials engineering and performance, 22.10 (2013) 3140-3146

Such materials are characterized by exhibiting time-dependent properties that change with the structural level of the material itself [2].
In this context, some constitutive models from the linear viscoelastic theory has been directly used to structured materials modeling [12-15].
The zero-shear-rate viscosity is linked to the viscosity of the completely structured material, so one can say that in more viscous materials the influence of the elastic modulus rate is more important.
Advances in Colloid and Interface Science Vol. 147 (2009), p. 214-227 [3] H.
Thompson: A unified approach to model elasto-viscoplastic thixotropic yield-stress materials and apparent yield-stress fluids.

Patel College of Pure and Applied Sciences, Charutar Vidya Mandal University, Vallabh Vidyanagar-388120, Anand, Gujarat, India 2Scientific-Practical Materials Research Centre, National Academy of Sciences of Belarus, 19 P.
Patel, Fabrication and electrical characterization of Al/p-ZnIn2Se4 thin film Schottky diode structure, Materials Science in Semiconductor Processing. 54 (2016)
Ahmad-Bitar, A study of the optical bandgap energy and Urbach tail of spray-deposited CdS:In thin films, Journal of Materials Research and Technology. 2 (2013) 221–227
Kamoun-Turki, Effect of substrate temperature on physical properties of Cu2FeSnS4 thin films for photocatalysis applications, Materials Science and Engineering: B. 254 (2020) 114509
Hafiz, Characterization of optical constants of Se30Te70 thin film: Effect of the thickness, Materials Science in Semiconductor Processing. 18 (2014) 1–5

Critical Reviews in Solid State and Materials Sciences, 36(4), 191­208
Critical Reviews in Solid State and Materials Sciences, 35(2), 125­152
Journal of nuclear materials, 225, 163­174
Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 17(4), 1335­ 1339
International Journal of Materials Research, 100(12), 1653­1661

In experiment, EDM machine tool D703F was used to machine nonferromagnetic materials.
Introduction It is difficult to implement that hard machining materials and parts with complex shapes or special requirements such as superfinishing or finishing operation are machined by conventional processes.
Chang: Journal of Materials Processing Technology, Vol. 201 (2008), pp.565-569
Lee: International Journal of Machine Tools & Manufacture, Vol. 48 (2008), pp.1179-1186
Cheah: Journal of Micromechanics and Microengineering, Vol. 14 (2004), pp.1526-1529.