Search results

Further cooling to -25 °C did not cause any noticeable changes in the structure (Fig. 1c).
Reheating to room temperature leads to the recovery of the original structure (Fig. 2c).
The dry film structure of C12Na at 25 ° C is similar to C8Na (Fig. 3a).
During heating from -25 to 25 °C the initial structure is fully restored (Fig. 3d, e).
Madsen, Humidity-modulated phase control and nanoscopic transport in supramolecular assemblies, Journal of Physical Chemistry B. 11 (2014) 3207-3217

As the properties are a structure sensitive, materials structure as well as crystal structure must be properly designed to meet a specific application.
An additional step is then required to promote solid state reaction for a composite structure formation.
The internal structure of sintered B3SF sample is shown in Fig.4.
The lamellar structure raised from cold welded particles can be clearly seemed in some particles.
Silmόes, Z., Alexandre, Cavalcante, Santo, Laccio, Ricardi, Santos, Carla, Varela, A., Josė, Longo, Elson, Feroelectric and Dielectric Behaviour of Bi0.92La0.08FeO3 Multiferroic Thin Films Prepared by Soft Chemistry Route, J.

For instance, Guozhen Shen group[3] has fabricated CdS Multipod-Based Structures through a thermal evaporation process.
Fig 2 shows a typical XRD pattern of the product deposited on the FTO substrate, which indicates that sample is mainly composed of cubic zinc blende-structured CdS (JCPDS Card, No.41-1049) and small amounts of orthorhombic structure Bi2S3 (JCPDS,17-0320).
The crystal structure of as-synthesized CdS branchedNanowire is determined by XRD.
The thus obtained have a single crystal structure, and are distributed on the substrate.
Yang，Advanced Materials, 2003, 15, 5: 353–389 [3] Pan AL, Liu RB, Yang Q, JOURNAL OF PHYSICAL CHEMISTRY B, 2005, 109, 51: 24268-24272 [4] Junwei Hou, Xiuchun Yang, Applied Surface Science, 2011, 257:7684–7688 [5] Zhiyong Fan, Haleh Razavi, Jae-won Do, Nature Materials,2009,8, 648-653 [6] Zhiyong Fan, Daniel J.

XRD analyses revealed Bi-layered perovskite structure in all samples.
Introduction Bismuth titanate, Bi4Ti3O12 (BIT), belongs to the family of ferroelectric materials with perovskite layered structures.
It is evident that the Bi-layered perovskite structure has been maintained after substitution of Gd for Bi.
Effect of titanium substitution on film structure and ferroelectric properties of Sr-deficient Sr0.75bi2.35Ta2O9 thin films[J].
Chemistry and Phys. 2006, 98: 481-485

Otherwise, the output of this series structure is ‘OFF’.
The numbers in Fig. 2 denote series structure of switches (201), the row control line of the series structure (202), and the column control line of the series structure (203) separately.
If the state of its ‘column switch’ is ‘ON’, the final state of this series structure is ‘ON’, the input of the series structure of switches can go through the series structure.
Or it will be ‘OFF’, the series structure has no output.
Analytical Chemistry, Vol. 77(7) (2005), p. 2266-2271.

This paper summarized hydrogen bonding structures between proton donors and proton acceptors.
Zhu, Analysis of organic molecular structure spectrum, Chemical Industry Press: Beijing, 2005, pp. 38-44
Nomura, Structure and properties of fatigued segmented poly (urethaneurea) s Ⅲ.
Ko, Structure and thermal properties of polyether polyurethaneurea elastomers, J.
Suchkova, Quantum chemistry studies of far-infrared spectra of aromatic urethanes, Spectrochim.

This determines the zonal structure of the partially oxidized pellets, i.e. a magnetite core and a hematite shell.
At these temperatures the swelling of hematite grains does not exceed 3% (Fig. 1), and the structure of both reduced and unreduced pellets is quite dense.
The structure of the pellets represents the assembly of cracked slag inclusions with practically no binder between the ore grains.
Low mechanical characteristics of the partially oxidized pellets are attributed to their zonal structure.
Geld, Physical Chemistry of Pyrometallurgical Processes, Part 1, Metallurgizdat, Sverdlovsk, 1962

Before calculating absorption structure, four SiC layers with the surface terminating H atoms were fully relaxed.
Fig 1 shows the optimized adsorption structures for 4H-SiC(000-1) surface.
For another surfaces, similar trend of the adsorption structure were observed.
The structures presented in the first row were optimized in the vaccum condition, while another structures were the optimized structures on the surfaces with interacting to the atoms in the surface.
GCMC result indicated that amount of adsorption was depending on the surface structure.

From structure and chemical, the characteristics of Nano-TiO2 are summarized.
But our domestic research is still at infancy in this field. 1 The Study of Nano-TiO2 1.1 Nano-TiO2 structure Divided from the performance of Nano-TiO2, there are three kinds of structure such as rutile, anatase and brookite.
Brookite is rare in nature because of its instability crystalline structure with no commercial value.
Nanometer photocatalysis material can be applied into concrete pavement better than the pitch structure in road engineering.
The most advanced research room of environmental catalysis is "chemistry and Engineering Department of Environmental Pollution Control Lab" in Beijing University of Technology.

Their unique physical and mechanical properties such as strength and lightness allow applications in numerous fields including material science, chemistry, engineering and physics [6, 7].
In their study, a SWCNT is regarded as a continuum-shell model which is compared to the discrete molecular structure linked by the C-C bond.
These nano-structures possess diameters ranging from 0.4 to 3.0 nm, with lengths of over 10 µm.
It was then assumed that CNTs, when subjected to loading, behave like space-frame structures.
Zhang, Molecular dynamic study of effects of Si-doping upon structure and mechanical properties of carbon nanotubes, Commun.