Search results

The aim of this paper is to use infrared thermography to analyze the macrostructure of engineered cementitious composites and their thermal performance.
The average strength of the cement compounds at 28 days varied from 27 to 40 MPa.
Journal of Alloys and Compounds 2004, 371:53–57
Journal of Materials Processing Technology 155–156 (2004) 1132–1137
Journal Key Engineering Materials 2006.

The aim of this paper is to show that recent progress in modelling of the role of grain boundaries in metallic materials offers new possibilities for optimizing their properties.
Nevertheless, the currently available models do provide a useful insight into the properties of so called special grain boundaries, with specific rotations angles, which comprise a significant fraction of the grain boundaries in ultra-fine- and nano-grained aluminium alloys (see for example [18, 19]).
Grain boundaries revealed in 2014 aluminium alloys: the coloured lines indicate the grain boundaries of mis-orientation angle from different ranges.
A finite element model of nano-polycrystalline aluminium alloy is shown in Figure 8.
Grain Boundary misorientation Effect on Intergranular Corrosion in Aluminium Sheets, 11 th International Conference on Aluminium Alloys, 21-23 September 2008, University of Erlangen-Nuremberg, Erlangen, Germany [22] Hu, Q.M., Yang, R.

The Nd2Fe14B intermetallic compounds have complex crystal structures, and sintered Nd-Fe-B permanent magnet materials microstructures are shown in Fig. 1.
The aim of this paper is to find a program including a reasonable combination of grinding parameters, lower surface roughness, surface morphology and surface wear resistance improvements, material removal rate increase MRR.
Acknowledgements This research project is very grateful to the National Natural Science Foundation “Basic research about ultrasonic honing critical chatter based on the theory of nonlinear dynamic systems” (No.: 50975265), Shanxi Province Natural Science Foundation project "Ultrasonic Light finishing the study of rare earth alloy technology "(No.: 2007011071), and Technological innovation and entrepreneurship in Taiyuan City, University special project “Application of ultrasonic technology in the rare earth alloy processing ” (No.: 08122,040).
Journal of Applied Physics, 1983, Vol.55(6), p. 2083-2087
Journal of Magnetism and Magnetic Materials, 1998, Vol.188(1-2), p. 125-137

In 1952 the discovery of the semiconducting behaviour of III-V compounds introduced a new range of materials.
Welker in Germany showed that the III-V compounds are semiconductors.
These were not an entirely new class of compounds, for example the crystal structure of indium antimonide had been determined 25 years previously, but it was only when they were made of moderate purity that their semiconducting behaviour could be seen.
In 1955 injection electroluminescence was shown in a number of III-V compounds and mixed crystals with metal point contacts.
The silver-based alloyed electrodes did not give injection electroluminescence.

The presence of Mg2Si particles with high melting point, good hardness and low density in alloys Al-Mg-Si will improve the mechanical properties of materials as well [5].
While for composites with low elongation that could be related to more formation of Mg2Si intermetallic compound which is obtained in the microstructure (see Fig. 3).
Badkul, "Effect of Al-TiB Master Alloy Addition On Microstructure, Wear and Compressive Deformation Behaviour of Aluminum Alloys," Trans.
Ghomashchi, "Boron-based refiner : Advantages in semi solid metal casting of Al-Si alloys," (2007). 3 [11] H.M.R.
Kang, "The solidification process of Al–Mg–Si alloys," Journal of Materials Science, (1997) 1443-1447

Aluminization has been proven to be an effective method for increasing the corrosion resistance of Ni and Co-based superalloys and iron alloys at high temperature.
The formation of an α-Al203 layer improves the behavior of these alloys under steam conditions [6, 8].
Other effective method for improving the oxidation resistance of this type of iron alloys is the addition of small amounts of Si to steel.
Hoyer, W, Structural properties of liquid Fe-Si alloys.
Journal of Non-Crystalline Solids, 2002. 306(1): p. 90-98

The mixture was rolled, aiming to produce the electrodes, cut into 6 mm diameter cylinders and then pressed onto circular stainless steel substrate.
Rao: International Journal of Nanoscience Vol. 4 (4-5) (2011), p. 559
Ghoreyshi: Journal of Energy and Environment Vol. 4 (1) (2013), p. 53
Alloys and Compounds Vol. 296 (2000), p.223

The microstructure rafting takes place as a result of γ' particles coalescence by a directional coarsening via diffusion of alloying elements.
The alloy contains (in at. %): Al, 12.1; Cr, 5.3; Co, 9.38; Nb, 0.85; Ta, 0.89; Mo, 0.69; W, 2.4; Re, 0.88 and Ni balance [14].
These arrows from NbTa-compound in interdendritic regions were formed during solidification (Fig. 2, a).
(a) Microstructure of the NbTa-compound "arrows".
Journal Plasticity Vol. 22 (2006), p. 2301

Introduction At present, polymer composite materials (PCM) are the most popular materials used in engineering; they not only substitute metals and alloys, but also increase the reliability and durability of machine parts operating under extreme conditions.
Plasma-chemical treatment (PCT) of carbon materials in the environment of organofluorine compounds is conducted to obtain fluoropolymer coatings several tens of nanometers thick on the surface of carbon fibers [13].
The formation of salts of carboxylic acids and compounds with epoxy groups on the surface of the samples after friction indicates the formation of a transfer frictional film.
These compounds act as inhibitors of oxidative processes and improve the wear resistance of PCM, as described in a number of works [18, 19].
Extended fluoroorganic compounds are registered on the surface of "Belum".

Aniline dissolves in organic compounds such as alcohol, benzene, chloroform and aceton.
Based on the aim of XRD that has been done, it can be identified the formation of two phases, where the phase consists of the main phase (BaM) and the secondary phase (Hematite).
Topkaya, Effect of Zn substitution on temperature dependent magnetic properties of BaFe12O19 hexaferrites, Journal of Alloys and Compounds 725 (2017) 1230-1237
Pubby, Effect of thickness on microwave absorptive behavior of La-Na doped Co-Zr barium hexaferrites in 18.0–26.5 GHz band, Journal of Magnetism and Magnetic Materials 423 (2017) 441–446
Yu, Hydrothermal synthesis of magnetic Fe3O4/graphene composites with good electromagnetic microwave absorbing performances, Journal of Magnetism and Magnetic Materials 426 (2017) 114-120