Search results

., 19, 220072 Minsk, Belarus 2 University of Texas at El Paso El Paso, TX 79968-0515, USA 3 Institute of Physics of PAS, al.
[3] E.L.
Subbanna et al., Solid State Commun. 129 (2004), 479

Mg solute atoms are the major factor causing this effect in Al-Mg alloys.
It can be concluded that the Al-Mg-0.42wt%Cu alloy possesses the highest strength.
The addition of Cu does not affect the n̄ values, as the n̄ value of Al-Mg-0.42wt%Cu alloy is comparable with that of Al-Mg-0wt%Cu alloy, only 1.1% lower.
El-Sebaie and Mellor[26] reported some calculation results based on the assumption of instability under the plane strain condition at the bottom of the cup wall.
El-Sebaie, P.B.

NIE, et al: Natural Gas Industry, Vol. 6(2008) p.48
[4] E.L.
Stark, et al: Geothermics, Vol. 36(2007) No.3, p.185-222
[15] E.L.
[16] E.L.

Box 179 New Borg El- Arab City, Alexandria 21934, Egypt. 2Environmental Engineering Department, Egypt-Japan University of Science and Technology, P.O.
Box 179 New Borg El- Arab City, Alexandria 21934, Egypt.
El-Badawy, A.
AL-Oqla, S.
Al Jawahery, A.

%El=CelCt×100% (1) Where EL is the percentage of the chemical element in the alloy, Cel is the concentration of the element in the alloy in ppm and Ct is the total concentration of all elements present in the alloy.
Al-Alimi et al., « Recycling aluminium for sustainable development: A review of different processing technologies in green manufacturing », Results Eng., p. 102566, 2024
Weidenhamer et al., « Metal exposures from aluminum cookware: An unrecognized public health risk in developing countries », Sci.
Stahl et al., « Migration of aluminum from food contact materials to food—a health risk for consumers?
[10] E.L.

Schulzeet. al. [5] had compared the machining strategies for drilling holes in chopped glass fiber reinforced polymeric (GFRP) composites.
El-Sonbatyet.al.used “Taylor Hobson Surtronic 3+” to obtain the surface roughness of the drilled holes of GFRP composites and measurements were taken at the middle of the holes wall[9].Varatharajanet. al. [10] used scanning electron microscope (SEM) to characterize the failure mechanisms on the drilled holes of glass fiber reinforced polypropylene (GFRPP) and GFRP composites.
El-gizawy and C.
Faria, et al., Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor, Int.
El-Sonbaty, U.A.

Experimental Superalloys on the basis of Ni-Al alloyed by refractory elements were the object of the study.
The alloy composition was chosen so that the ratio of Ni and Al in the sum with the other elements replacing the sites of the Al in the L12 superstructure was 0.77 / 0.23.
Kachanov et al., Nickel-base superalloy single crystals, Engineering, Moscow, 1997
Konovalova, E.L.
Nicholson et al.

Presence of crystalline and microcrystalline deposits during electroless Ni-P deposition is also reported by Sankara Narayanan, et.al [2] and Agarwala et.al [11].
Such preferred orientations are reported by Su Hoon Park et.al [12].
Table 2 EDS analysis (in at %) for Al, P, Ni at various locations given in fig 2a, 3a and 4a.
Abo El-Enine, Electroless deposition of Nickel-Copper-Phosphorous alloy on Aluminium, Galvanotechnik, 102 (2004) 2876-2881
[7] E.L.

Leonard et al. [10, 13] reported the endothermic peak for the first time in the literature.
Later, Loufakis et al. [16] noted that this peak disappeared during the second heating.
According to El-Mohajer et al. [11] the amorphous-crystal interphase depends on the crystalline phase area (smaller crystals having greater area lead to a larger amount of the interphase).
Al-Raheil, Polym.
El Mohajir, N.

Simultaneously, Aluminum-glass (Al-glass) substrates were prepared by evaporating 30nm Aluminum and were used throughout this study as PVDF/MgO substrates.
The PVDF/MgO(7%) solution was spin coated on Al-glass at 1500rpm for 90s.
As stated by Mohajir et. al., and Tang et. al., the temperature between 70 to 100ºC were found to convert α-phase of PVDF to β-phase which contributed to the increased in the dielectric constant[1, 4-5].
El Mohajir and N.
El Mohajir and N.