Search results

Fig. 2 Engineering stress-strain curves for CP iron with GB micro-voids at room temperature with various strain rates from 1.0 × 10-5 s-1 to 1.0 × 10-2 s-1.
(a) =1.0×10-5 s-1, (b) =1.0×10-4 s-1, (c) =1.0×10-3 s-1, and (d) =1.0×10-2 s-1.
(a) =1.0×10-5 s-1, and (b) =1.0×10-2 s-1.
References [1] C.
A, Vol. 479 (2008), p. 76

After 1 pass, the hardness increases highly in Fig. 1.
Especially, the hardness was decreased slightly at over 100° C/ 1 hour and highly at over 300° C/ 1 hour annealed samples in Fig. 1.
Cube component, {001}<100>, shows high values in initial Al sheet, decreases remarkably at 1 pass ECAPed Al sheet, increases at 200° C/ 1 hour annealed Al sheet, and increases at 400° C/ 1 hour annealed Al sheet.
References [1] V.M.
Forum Vol. 475-479 (2005), p. 417 [14] H.J.

The addition of 1% nano metakaolin acts as an ultra-filler and refines the microstructure of concrete.
The size of nano materials to be used in concrete must less than 500 nm [1, 2].
Finally NK and NC were act as additives based on percentage from 1% to 9%.
Conclusions From this research, the conclusions included are drawn as follows: 1.
Construction and Building Materials 30 (2012) 470–479, 2012

A summary of the detected levels is shown in Table 1.
Fig.1.
Tab.1.
References [1] K.
Awshalom, Nature 479 (2011) 84

This gel dried in the oven at 150°C for 1 hour, then pounded manually for 1 hour.
Result and Discussion 1.
Table 1.
References [1] X.
Solid State Communications, 147(11–12), 479–483, (2008). https://doi.org/10.1016/ j.ssc.2008.06.040 [10] H.

Fig. 1.
The long-lived component with the lifetime τ3 > 1 ns and intensity I3 < 1, associated with the annihilation of positronium was not taken into account.
Table 1.
References [1] W.
Pundt, Hydrogen-induced defects in Niobium Journal of Alloys and Compounds, (2007) 479-483

Table 1.
Mutations previously mentioned in literature From tables 1 and 2, only isolates 1 and 5 had a change in Arg-136 to Ala-136 and Cys-136, respectively.
For isolate 1, residues 163 and 167 are binding to ADPNP (5’-adenylyl β,γ-imidodiphophate) Figure 1.
References [1] F.
Maxwell, Exploiting bacterial DNA gyrase as a drug target: current state and perspectives, Appl Microbiol Biotechnol 92(3) (2011) 479-97

Figure 1 depicts this plot comparing the behaviour of the [001] Cu single crystal to that of the dispersed-alumina high conductivity Cu.
The separation between the ¼ and 1/10 rate changes also indicates the presence of obstacles other than forest dislocations. 0 1 2 3 4 5 2468101214161820 b 2λ/v θII 22 /θ 0.036 0.08 0.3 0.3 17 h 17 h 0.5 h 0.5 h Al [001] 0.35 0.22 Figure 4a.
The filled and unfilled symbols indicate ¼ and 1/10 down-rate changes respectively.
References [1] H.
Forum Vol. 475-479 (2005) p. 337

Two types of models were used: the small cube with the dimensions 1.5x1.5x1 mm3 and the tall cube with the dimensions 1.25x1.25x5 mm3.
An example of a predefined fiber texture is shown in Fig. 1(b).
Fig. 1.
References [1] L.
Tintillier, “Three-dimensional probabilistic simulation of solidification grain structures: Application to superalloy precision castings,” MTA, vol. 24, no. 2, pp. 467–479, Feb. 1993, doi: 10.1007/BF02657334

T / oC T / oC T ime 1 minute 1400 1400 T1 (1 min) T2 (2 h) 1150 T ime T / oC T ime T1(1 min) 1400 1250 T / oC T ime 2 hours 1400 T2(2 h) SSS profile 1 (Sample 1) TSS profile 2 (Sample 2) TSS profile 3 (Sample 3) SSS profile 4 (Sample 4) Fig. 1, The various sintering profile employed in this work.
For sintering profiles, refer to Figure 1.
For sintering profiles, refer to Figure 1.
Table 1.
References [1] R.C.