Search results

Yazdani, Application of neural networks for estimation of concrete strength, Journal of Materials in Civil Engineering, 16(3) (2004) 257-264
Sarıdemir, Prediction of compressive strength of concrete containing fly ash using artificial neural networks and fuzzy logic, Computational Materials Science, 41(3) (2008) 305–311
Yeh, Modeling concrete strength with augment-neuron networks, Journal of Materials in Civil Engineering, 10(4) (1998) 263-268
Kuo, Spatial interpolation using MLP–RBFN hybrid networks, International Journal of Geographical Information Science, 27(10) (2013) 1884-1901
Irvine, CA: University of California, School of Information and Computer Science (2010).

Journal of Drug Delivery Science and Technology 33 (2016): 136-142
Journal of Drug Delivery Science and Technology 37 (2017): 74-80
Journal of Biomedical Materials Research Part A 79.3 (2006): 582-590
Key Engineering Materials.
Journal of biomedical materials research 61.3 (2002): 421-429.

Machado, The machinability of nickel-based alloys: a review, Journal of Materials Processing Technology 86 (1999), 1-16
Teo, The machinability of Inconel 718, Journal of Materials Processing Technology 63 (1997), 199-204
Elbestawi, Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials, Int.
Journal of mechanical Tool Manufact 36 (5) (1996), 611–634
Mannan, Machinability of nickel-based high temperature alloys, Machining Science and Technology, 4 (1) (2000), 127-168

Biological degradation of waste materials was used much due to its cheap, eco-friendly, and less sludge producing properties[7].
Materials and methods 2.1 Dyes and chemicals An effluent sample collected from sludge samples of an anaerobic reactor of DHU University, China.
Materials Science and Engineering: C. 2013. 33(4): 2258-2265
Journal of Hazardous Materials. 2011. 190(1–3): 351-358
Journal of Hazardous Materials. 2009. 171(1-3): 654-659

Černý, Cement Composites for High Temperature Applications, Advanced Materials Research 982 (2014) 154-158
Černý, Pore Distribution and Water Vapor Diffusion Parameters of Lime Plaster with Waste Brick Powder, Advanced Materials Research 1054 (2014) 205-208
Polozhiy, Residual Strength of Thermally Loaded Mortars with Treated Municipal Solid Waste Incineration Fly Ash Used as Supplementary Cementitious Material, Advanced Materials Research 982 (2014) 114-118
Xu, Dynamic Compressive Behavior of Ceramic Fiber Reinforced Concrete Under Impact Load, Construction and Building Materials 45 (2013) 475-488
Czigány, Effect of Fiber Surface Treatment on the Mechanical Response of Ceramic Fiber Material-Reinforced Interpenetrationg Vinyslester/Epoxy Resin, Composites Science and Technology (2004) 1717-1723.

So it is helpful to make material removal on work piece surface.
The calculation formula of Chinese National Natural Science Foundation (No. 50875242), Key Project of Zhejiang Province Natural Science Foundation (No.
So it is helpful to make material removal on work piece surface.
Luo: Chinese Science A compiling Vol. 29(4) (1999), p. 366 [2] C.G.
Zhou: Chinese Science G compiling Vol. 33(1) (2003), p. 76 [4] C.G.

The particleboard of larix gmelinii and UF resin were used as main raw materials.
However, the sources of VOC emissions are complicated, such as raw materials and manufacturing techniques.
Materials and methods Materials.
Forest products journal.
Forest Products Journal.

Nanosized particles possess characteristic physical and chemical properties different from those of bulk materials due to the confinement of electrons, excitons, and photons into small volumes.
In the following measurements, 50nm and 5000nm Cu powders wrapped by the same insulating materials are measured at the same time.
Acknowledgements Support for this work by National Science Council of the Republic of China under grant No.
Zhang: International Journal of Heat and Mass Transfer Vol. 49 (2006), p. 1489 [3] C.
Xiao: International Journal of Heat and Mass Transfer Vol.48 (2005), p. 3932 [4] S.

Hu, Squeeze casting of magnesium alloys and their composites, Journal of materials science, vol. 33, no. 6 (1998) 1579-1589
Hu, Influence of Applied Pressure on Microstructure and Tensile Properties of Squeeze Cast Magnesium Mg-Al-Ca alloy, Materials Science and Engineering A, vol. 528 (2011) 3589-3593
Lo, Microstructure and tensile properties of squeeze cast magnesium alloy AM50, Journal of materials engineering and performance, vol. 14, no. 4 (2005) 539-545
Jin, Refinement mechanism of in-situ Al4C3 particles on AZ91 magnesium alloys, Journal of Wuhan University of Technology Material Science, vol. 29, no. 1 (2014) 154-158
Liu, Grain refinement of AZ31 magnesium alloy by new Al-Ti-C master alloys, Materials Science and Engineering A, vol. 473, no. 5 (2008) 16-27.

Tensile tests of the composites were carried out in a WDW-100 materials tester.
Baboux: Composites Science and Technology Vol. 60(2000), p. 913 [8]L.
Guo: Materials science & engineering: A Vol. 366(2004), p. 144 [15]S.P.
Qiao: Composites Science and Technology Vol. 57(1997), p. 623 [17]Z.Y.
Woo: Journal of Composite Materials Vol. 30(1996), p. 985 [19]T.W.