Search results

All samples were characterized by X-ray diffraction data on a Philips model PW 1830/80 diffractometer using Cu-Kα radiation.
The decrease of the specific surface area of the ceramics with an increase of the sintering temperature occurred because of the pore size reduction and the closure of the superficial pores.
The highest pore volume measured belongs to ceramic sintered at 1000o C, with a distribution of mesopores (0.01-0.03µm) and macropores (0.4-0.9µm). 1000 1050 1100 1150 1200 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Specific surface area (m 2 /g) Temperature (ºC) Figure 2 Specific surface area for the ZnO-TiO2-Ta2O5 sintered ceramics measured by BET nitrogen adsorption. 0,01 0,1 1 0 10 20 30 40 50 Dv(r)x10.000 (cm 3 /µµµµm x g) Pore Radii (µµµµm) 1000ºC 1100ºC 1200ºC Figure 3 Pore size distribution curves of the sintered ceramics calculated from the mercury porosimetry data.
The data obtained for the sample sintered at 1100o C certainly possesses some experimental errors, because both capacitance and impedance measures invert its behavior starting from 43% of relative humidity, being in disagreement with the expected results.

Perturbation guidance system design How to take advantage of the flight trajectory data measured by GPS guidance to predict the no control impact point is the most important issue.
The range deviation solver method is essentially data summarized, to establish the range of deviation model accuracy depends on the sub-sample representativeness.
Regression calculation these data can be obtained by the approximate equation residual range forecast.
[3] Jitpraphai,T., and Costello,M., “Dispersion Reduction of a Direct Fire Rocket Using Lateral Pulse Jets”, Journal of Spacecraft and Rockets, Vol.38, No.6, 2001, pp.929-936

The Arrhenius plots plotted based on the data obtained from the study of effect of temperature on the rates of formation and decomposition of formic acid and formaldehyde in the temperature range 30-50°C revealed the activation energies of these reactions.
Reduction of CO2 to methanol by following chemical methods.
Guo, CO2 activation and total reduction on titanium (0001) surface, J.
Peris, A new approach to the reduction of carbon dioxide: CO2 reduction to formate by transfer hydrogenation in iPrOH, Organometallics, 29 (2010) 275-277
Utility Data Institute, 2003.

Cloetens4, f 1 CENIMAT - Centro de Investigação em Materiais, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, Quinta da Torre, Caparica 2829-516, PORTUGAL 2 CIICS - Centro de Investigação em Interfaces e Comportamento de Superfícies, Universidade do Minho, Campus de Azurém, Guimarães 4800-058, PORTUGAL 3 Laboratoire des Composites Thermostructuraux, Université de Bordeaux 1, Domaine Universitaire 3, Allée la Boétie, F 33600 Pessac, FRANCE 4 ESRF - European Synchrotron Radiation Facility, Polygone Scientifique Louis Néel - 6, rue Jules Horowitz, 38000 Grenoble, FRANCE a ajv@fct.unl.pt, b fbf@fct.unl.pt, csccf@fct.unl.pt, d lrocha@dem.uminho.pt, e vinhola@lcts.u-bordeaux1.fr, fcloetens@esrf.fr Keywords: Computed tomography, Microtomography, Image analysis, Data processing, Metal matrix composites, Functionally graded materials, Microstructure, Interface, Damage.
Further development and possibilities Data processing.
Figure 4 - a) Reduction of processing time achieved with parallel computing for the hysteresis operation on a 100 × 100 × 100 SiCp FGMMC tomographic dataset.
Quaresma, from CITI (Centro de Investigação em Informática e Tecnologias da Informação/UNL), for their role in the development of the data processing tools.

High-energy x-ray diffraction experiments were performed to obtain reliable diffraction data for the liquid phase of metallic glass-forming Zr-Cu binary alloys.
The data acquisition process was repeated typically three times to confirm the stability of the intensity profile obtained.
The total structure factor, S(Q), was extracted by normalizing the corrected coherent intensity data.
The RMC method has been shown to be a useful tool to construct a three-dimensional structural model of disordered materials using mainly experimental diffraction data [17].
The data of the constituent elements near their melting point were taken from the literature for a comparison [20].

Data on the current sharing capability of the PiN rectifiers is also presented.
A negative differential co-efficient of on-state voltage drop is also observed from Figure 2(b), which is due to the reduction of knee voltage at higher temperatures.

These overall data will be essential information for the development of antimicrobial films and coatings in food packaging with the extending shelf life.
However, higher temperature under heating process during plasticization is sometimes required but is not a good choice since it may cause serious detrimental effects on a shelf life of chitosan as well as possible reduction in antimicrobial activity [1].

To achieve accurate forecasting, the study utilizes data from newly connected domestic customers and their corresponding sanctioned loads from service centers in Bahir Dar (Bahirdar1 and Bahirdar2), Adet, Anbesamie, and Merawi. 2.2 Dataset Preparation Data collection began in May 2019, coinciding with EEU’s transition from a manual billing system to an Enterprise Resource Planning (ERP) system, ensuring data accuracy and reliability.
The data collected is below in Table 1.
Using this data, it regulates an oscillator to produce an output signal that remains synchronized with the reference signal[15].
Monthly diesel consumption data from the EEU Bahir Dar District reveals an annual operating cost of 571,663.35 ETB for the generators.
Taylor, “Assessment of Typical Meteorological Year Data in Photovoltaic Geographical Information System 5.2, Based on Reanalysis and Ground Station Data from 147 European Weather Stations,” Atmosphere (Basel), vol. 14, no. 12, Dec. 2023, doi: 10.3390/atmos14121803

The acceleration data of the activities with the characteristic quantity SVM and SMA was analyzed.
In recent years, with the development of social economy, the change of the living way, the miniaturization of family structure, and the miniaturization of floating population, the reduction of children, Separate tendency of generation live, the growth of life, the empty nester rate of old family is continually increase.
In the traditional detection method by using the threshold, due to the acceleration data of run and jump changes faster, with whose amplitude are larger, the division of the two activities and fall is very difficult.

This research paper highlights the flow of air from crankcase port with correspondence with amount of variable supply of current to obtain the experimental test data which is important to maintain the vehicle temperature inside the compartment for passengers comfort.
Reduction of Pc pressure makes the swash plate angle maximum (as Pd to Pc closed).
For obtaining suitable data all the strokes need to set within the value limits.