Search results

In this paper, the effect of ultrasonic wave on sizing materials is analyzed to optimize sizing properties.
By comparing with the traditional method of mixing and cooking, the relationships between sizing materials’(s) gelatinization temperature and time ,viscosity and viscosity stability are discussed.
The stirring of the magnetic rotor and ultrasonic help the dispersion of sizing materials in water, and gradually spread into good dispersion.
Conclusions Ultrasonic has a great impact on the viscosity of sizing solution in the mixing and cooking of sizing materials.
Journal of Textile Research, 2006, 27(10):96-98 [4] K.

Introduction Theoretically, all materials are heterogeneous at a sufficiently fine scale.
In a classical local continuum approach many materials can be treated as homogeneous continua through separation of the scale of the problem under consideration and the lower scales of heterogeneities affecting physical processes.
The research has been carried out within the projects “Multiscale Numerical Modeling of Material Deformation Responses from Macro- to Nanolevel” (Croatian Science Foundation, 2516); “Multiscale Modeling of Heterogeneous Structures” (Alexander von Humboldt Foundation, Germany) and “Centre of Excellence for Structural Health” (EU IPA2007/HR/16IPO/001-040513).
Tonković, et al., Key Engineering Materials 627 (2015) 381-384
Tonković, et al., Journal of Multiscale Modelling 04(04) (2012) 1250013.

When the peak pressure of the shock wave exceeds the dynamic yield strength of the processed materials, the strain hardening occurs on the material surface, and results in larger compressive residual stress, while some changes happens in its micro-structures, that significantly improves the material fatigue resistance, wear, stress corrosion, and etc [7-8].
Laser shock wave was used to strengthen the surface of QT800 materials in this paper, the effects of shock processing on fatigue properties of QT800 for the crankshaft was analyzed with fatigue test, that provides a theoretical basis for enhanced treatment.
The sample material is QT800, and the sample size is shown in Fig.1.
The processed surface by laser shock was compressive residual stress, that could relaxed stress concentration inside of the material, that id benefit to delaying the fatigue cracks expansion and extending service life of the materials.
References [1] Ren XD, Zhang YK, Zhou JZ and et al: Journal of Jiangsu University (Natural Science Edition) Vol. 28, (2007), p. 289 [2] Liu RC, Xue LQ, Ma SM and et al.

Wang, An experimental study on size effects on flow stress and formability of aluminm and brass for microforming, Journal of Materials Processing Tech. 184 (2007) 42-46
Wang, Effects of Grain Size on Micro Backward Extrusion of Copper, Advanced Materials Research. 83-86 (2010) 1092-1098
Chan, Geometry and grain size effects on the fracture behavior of sheet metal in micro-scale plastic deformation, Materials & Design. 32 (2011) 4738-4746
Chan, Geometry and grain size effects on the fracture behaviour of sheet metal in micro-scale plastic deformation, Materials & Design. 32 (2011) 4738-4746
Lai, Size effects in thin sheet metal forming and its elastic–plastic constitutive model, Materials and Design. 28 (2007) 1731-1736.

In recent years, RSM has been employed for optimizing the extraction process of polysaccharides, flavonoids, polyphenols, lysergol, chlorophyll-a, edible oil from various materials [10-18].
Materials and methods Experimental chemicals.
Wang: Medical Journal of Wuhan University Vol. 30 (2009), p. 89
Ali: Journal of Pharmaceutical Innovation Vol. 6 (2011), p. 88
Ho: Journal of Food Science and Technology Vol

Abstract: The performance of the aluminum alloy makes it the most popular lightweight materials for the automobile manufacturers.
It is made by aluminium alloy 6016-T4, the material performance parameters are shown in Table 1.
Materials Science and Engineering : A, Vol.280: 37-49 [2] Barlat F, Berm J.C., 2003.
International Journal of Plasticity, Vol.19(9):1297-1339 [3] CHEN W, CHEN H-h, XIE J, LIU J-x, et al, 2008.
Journal of Hunan University ( Nature Science), Vol.30(5): 29-33

In sintering process, different procedures were used to synthesize the LiFePO4/C composite materials.
In this paper, the LiFePO4/C composite materials were produced by the combination of electrospinning and sintering process.
LTD), polyacrylonitrile (PAN) (Mw=150000 (Typical), Sigmal-aldrich) were used as starting materials for electrospinning.
Preparation of LiFePO4/C composite materials The electrospun LiFePO4 precursor/PAN mats were heat treated in two steps.
Munichandraiah: ACS Applied Materials & Interfaces Vol. 2, No.7 (2010), p.2031-2038 [7] Jiajun Wang, Xueliang Sun: Energy & Environmental Science Vol. 5 (2012), p. 5163-5185 [8] Hao Hsun Chang, Chun Chih Chang, Hung Chun Wu, et al: Journal of Power Sources Vol. 158 (2006), p. 550-556

The concept of flow is to make parts ideally one piece at a time from raw materials to finished goods and to move them one by one to the next workstation with no waiting time in between.
Problems Statement in existing system The productivity of the company mainly depends on the accurate supply of required quantity of the materials.
The analysis of the current system showed that more resources than that assembly and thus these waste are to be removed and the flow materials are to be more streamlined.
Supplier with material flows. 6.
Journal of Manufacturing Technology Management 2011: 22: 4

Simulation of Deformation Behavior of Polymeric Materials by Chain Network Model Akira Shinozaki1, a , Kikuo Kishimoto1,b and Hirotugu Inoue 1,c 1 Department of Mechanical and Control Engineering, Tokyo Institute of Technology 2-12-1, O-okayama, Meguro-ku, Tokyo, 152-8552, Japan a sinozaki@mep.titech.ac.jp, bkkishimo@mep.titech.ac.jp, cinoueh@mep.titech.ac.jp Keywords: polymer, stress, degradation, simulation, molecular chain, network model Abstract.
It is important to understand the relationship between the mechanical properties of polymeric material and meso-scale structure.
Mass-spring modeling Actually, molecular chains of Polymeric materials have many kinds of length, and entangled each other.
The elongation of polymeric materials exhibits local deformation.
Yoshida: Internatinal Journal of Mechanical Sciences, Vol. 45 (2003), P 1863 [6] Marc S.Lavine, Numan Waheed, Gregory C.

Materials Science & Engineering C.41(2014)100-118
Materials Science & Engineering C.41(2014)100-118
Materials Research Express. 5(2018) 075509
Journal of colloid and interface science. 2019; 550:180-189
Journal of Materials Chemistry B.2017; 5:5549-5555