Search results

Ø The raw materials used to manufacture metal matrix nanocomposites include Al7075 along with reinforcement materials, i.e. silicon carbide (SiC) and Al2O3 particles improve wear characteristics.
Materials Science and Engineering: A. 799:140341, (2020)
InAdvanced Materials Research, Trans Tech Publications Ltd.. 1148, 109-114, (2018)
Materials and Technology,(2015); 49(1):9–13
Materials Science, 2014; 5:908–17

Failure Analysis of Metallic Materials in Sheet Metal Forming using Finite Element Method Pedro Teixeira2,a , Abel D.
The optimisation of sheet metal processes by using numerical simulations has become a key factor to a continuously increasing requirement for time and cost efficiency, for quality improvement and materials saving, in many manufacturing areas such as automotive, aerospace, building, packaging and electronic industries.
The introduction of new materials brought new challenges to sheet metal forming processes.
Lemaitre: Journal of Engineering Materials and Technology, Transactions of American Society of Mechanical Engineers Vol. 107 (1985), p. 83
Saporita: Materials Science Forum, Vols.455-456 (2004), p. 707

Experimental Materials.
References [1] Zeng Aixiang, Xiong Weihao, Xu Jian, Materials Letters 59 (2005) 524-528
Rahman, Applied Surface Science 181 (2001) 35-50
Materials Letters 57 (2002) 151-156
[4] Sung-Soo Kim, Seon-Tae Kim, Joon-Mo Ahn, Keun-Hong Kim, Journal of Magnetism and Magnetic Materials 271 (2004) 39-45

For the 800 oC sample, the materials seem to be more crystalline with individual polyhedral shapes.
The XRD patterns of all the materials are matched to the ICDD reference pattern number 01-089-2810 which is α-Fe2O3 rhombohedral structure with space group R-3c.
Therefore, it can be seen that purity, phase and crystal size are dependent on the heat treatments done on the materials.
This parameter also affecting the crystallite size and morphology of the materials.
El-Shahat: submitted to International Journal of Inorganic Chemistry (2010) [9] D.

Materials and Methods Location of Study Area: Associated Granite Industries (AGI) Limited deposit is located on the co-ordinate (latitude 30 18' 25'' E and longitude 70 15' 15'' N).
Jacobson: Micro-scratch Evaluation of Rock Types - A Means to Comprehend Rock Drill Wear, International Journal of Rock Mechanics and Mining Science, Vol. 37 No. 2 , ( 2004), pp 203 – 210
Teale: The concept of Specific Energy on Rock Drilling, International Journal of Rock Mechanics and Mining Science Vol. 2, (1964), pp. 57-73
Pourrahimian: Development of a New Classification System for Accessing of Rock Mass Drillability Index (RDi), International Journal of Rock Mechanics and Mining Science, Vol. 45 (2008), pp 1 -10
Osanloo: A New Classification System for Evaluating Rock Penetrability, International Journal of Rock Mechanics and Mining Science, Vol. 46 (2009), pp 1329 -1340

Especially, after the vibrating screen sustained thousands or millions of circular loads, brittle fracture will occur even if the screen box’s nominal stress is far less than the strength limit of materials.
E—the connecting area of the baffle of material added to screen box.
The vibration fatigue S-N curve of the vibration screen material are identified through the sample test, the test material has the same characteristic, constraint condition and load as vibration screen.
Mechanical Science and Technology. 19Supplement(2000)56 [5] Z.J.Yin and J.P.Liu:Stress analysis of large vibration screen under alternate load.
Journal of Tianjin University. 40(2007)57 [6] Q.T.Guo and C.P.Zhang:Reliability design of fatigue strength of 2ZK3675 linear vibration screen.

Silicon can retain its semiconductor characteristics even at a high temperature while the other semiconductor materials cannot.
Prior to this time, radiation effect studies involved investigation of only the bulk properties of semiconductor materials and devices.
Accordingly, much effort followed in the pursuit of various doped and otherwise modified gate dielectric materials.
Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms. 267(18), (2009) 3032-3036
A Journal of Science and Technology. 2 (2008) 59-69.

However, titanium and its alloys are usually considered as extremely difficult to cut materials because of their low modulus of elasticity, high chemical reactivity with cutting tool material and its high stress and strength ratio at elevated temperature makes the machining further difficult [3, 4].
Configuration of cutting tool and workpiece material.
Nurul Amin, American Journal of Engineering and Applied Sciences. 2 (2009)147-153
Dai, Influence of cutting conditions on the cutting performance of TiAl6V4, Advanced Materials Research. 337 (2011) 387-391
Maranhao, A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis, Materials and Design. 30 (2009) 160-165

Experimental Materials.
He: Materials Science and Engineering: C Vol. 92 (2018), p. 1092 [4] M.K.M.
Mihailescu: Journal of Applied Polymer Science Vol. 134 (2017) [7] M.
Lloyd-Jones: Materials Today Communications Vol. 19 (2019), p. 286 [14] S.E.
Zawadziłło: Materials Vol. 14 (2021) [16] J.

This anisotropy is believed to stem from the strong texture found within the material, which is the Goss texture commonly found in low stacking fault energy materials.
Acknowledgements The authors would like to thank the National Science Foundation- Division of Materials Research, Grant # 706446, for its support.
All materials characterization was done at the Nanoscale Materials Characterization Facility in the Department of Materials Science at the University of Virginia.
Barnard: Journal of Applied Physics Vol. 97 (2005), p. 10F301-1
Hadjipanayis: Journal of Magnetism and Magnetic Materials Vol. 200 (1999), p. 373