Search results

The data show that the arcing process is associated with the generation of a grey colour, which probably results from partial reduction due to localised melting [17,18].
These data show the following trends (Table 2): Table 2.
From these data, the following observations can be made with regard to the effect of the different parameters, as summarised below: 1.

The voltage and current data of electrodes acquired by oscilloscope is transmitted to the control computer.
The control computer analyses the data and estimates the state of discharge, then sends the proper control codes to amplifier to output the corresponding power level.
Similarly, in the plasma flow control applications, discharge state control is to maintain the effective drag reduction by the control system of flight.
The control program written in C# language includes initiation of NI measurement studio, starting and stopping power level measurement, discharge state control, data process and display.

The program Fit2d was used for data reduction [5].
Diffraction data were taken during welding with a feed rate of 5 mm/s at various locations around the welding spot.
In this case, data taken from the same location as discussed above were analysed.

To achieve this goal, industrial waste can be used in the production of cement, which leads to a reduction of CO2 emissions and the use of natural resources.
However, data in the scientific literature on the effect of additives on the crystallization of these compounds and their properties are incomplete and often contradictory.
The CuKα radiation (U=40 kV and I=40 mA), 0.02 mm Ni filter, a Bragg–Brentano geometry, and a fast counting detector Bruker LynxEye were used for collect data.
The duration of hydrothermal treatment was 16 h (a and c) and 72 h (b and d) The XRD results were confirmed by STA analysis data.

However, the knowledge of how the magnetic field affects the kinetics of atomic diffusion in ferromagnetic materials is still lacking, and the corresponding experimental data are scarce.
The forged and hot rolled Fe sheet was further processed by two-step cold rolling with the total reduction of 85%, followed by recrystallization annealing at 850 °C for 80 s.
Interpolation (for the field of 5 kOe) and extrapolation (for zero field) of his data for the temperature of 747 °C gives M=5.58·10 -2 T and M=6.15·10 -2 T for the zero and 5 kOe magnetic fields, respectively.
However, the data on temperature dependence of surface [4] and dislocation pipe [6] self-diffusion indicate that magnetic effect in short-circuit selfdiffusion is much stronger than in the bulk one.

Introduction The methanogenic bacteria are a diverse group of anaerobic archaebacteria, and metabolically are divided into those that specialize in CO2 reduction and those that also use acetate and/or methyl compounds [1, 2].
., Cary, NC, USA) was used for the experimental design and regression analysis of the data obtained.
The experimental data represented the means calculated from three independent samples Figure 2.
The experimental data represented the means (with standard deviation) calculated from five independent samples TABLE II.

The data are summarized in Table 1.
Thermal data for the dehydration and decomposition of the complex contain latticed water.
Combine the IR, electronic absorption, and elemental analysis data the imaginable structure of the complex was given in the Scheme 1.
Increasing rutin-Mn concentration caused a reduction in the fluorescence of serum albumins, It is interpreted that the complex-system formed between serum albumins and rutin-Mn [7].

The study also compared the predicted model data with the experimental results for both a single overload and multiple overloads.
The Wheeler's model modifies the constant amplitude crack growth rate by a reduction factor, Cp [5].
The data of the model were compared with experimental results and Wheeler's model data.

Figure 4: Truss T03 - Sketches on site and photographs Figure 5: Thematic map -Truss T08-front east Figure 6: Thematic fiches T01 The Timber Material Data recorded during the inspection of the roof have been organized in thematic maps and fiches, for the structural system and each member (Fig. 5, Fig. 6).
Diagnosis, Safety Evaluation and Design of the Intervention Data collected during the investigation campaign were used for the analysis of the trusses.
The Italian standard D.M.LL.PP. 14.01.2008 introduces a reduction factor FC>1 for material strength, which depends on the reliability of data about the structure.

RTI provides the general service for interaction between of each simulation application, including the simulation application management, statement management, unavailability of accessing rights made management, time management, data distribution management and application programming interface.
The simulation application software Grid simulation system Power grid simulation is the foundation and the key of the training simulation system, provide the correct flow data and information of protection operation for substation simulation and substation automation system simulation, and to reflect all interaction between transformer substations and influence each other.
In the power grid simulation, the dynamic method of equivalent of the network simulation to the local grid for reduction, guarantee the accuracy of the power grid simulation, establishing dynamic mathematical model of each element in the power system, by the transient, middle and long process integration calculation method, realization to the dynamic simulation of the power grid.
Management function of trainer system mainly includes time management, user management, operation mode management, ensure higher practicability and usability of the simulation system; The preparation before training include the choice of operation mode data, setting initial way, the default fault and events; In the process of training operation and control refers to the trainer control the process of training , the operation of the model in power system, the setting of the fault and events, management and monitoring students operation; After the training analysis and assessment of including analysis the effect of operation trainees by using the event log, curve and statements, and other tools ;Use of accident treatment the students recall the process of representation and the changing process of the system ;Use evaluation tools to evaluate the operation of student.